background image

7-Port USB2.0 Metal Hub with DIN RAIL Mounting Kit

 

 

 

2

 

 

Upstream Port Connector:

 Type-B connector from upstream 

USB2.0  port.  It  is  connected  from  host  or  another  USB2.0 

hub. 

 

Self Power Input Connectors: 

This 2-pin (one pin plus voltage 

and  the  other  pin  is  GND)  terminal  block  connectors  are 

used  to  connect  strong  power  to  self-power  the  hub,  the 

voltage can be in the range from +7V to 24VDC.   

 

Warning!!

 

Please make sure the polarity of the input power should be 

correctly  match  the  terminal  block  pins,  otherwise  it  will 

damage the hub.

 

 

 

 

 

 

 

 
 

1.

 

Use static electricity discharge precautions. 

Remove  possible  static  discharge  potential  from  any 

objects  that  the  hub  may  come  in  contact  with  before 

installation. This can be accomplished by touching a bare 

metal chassis rail after you have turned off the power.   

2.

 

Apply  DC  power  (range  from  +7V  to  24V)  to  the  2-pin 

Terminal  Block  Connector. 

The  hub  was  bus-powered  by 

the upstream USB port, this terminal block connector is to 

add power to ensure enough power for the 7 downstream 

ports.

   

3.

 

Connecting  USB  Host  cable: 

The  host  cable  is  either  a 

standard  A-to-B  USB2.0  cable  or  a  screw-lock  type  A-to-B 

cable.  Please  connect  the  type-A  end  connector  of  the 

cable to your upstream USB port, then connect the type-B 

3. Hardware Installation 

 

-+7~24V 

-GND 

 


Содержание USBG-7DU2S






Отзывы: