background image

 

Cool Boss Evaporative Air Cooler 

25

 

P/N 5900274 — August 2022 — Rev. A1

 

Maintenance 

 

DANGER

 

Disconnect the unit from its power source 

before 

performing any maintenance! 

Verify the unit is locked out from power and cannot be energized while maintenance 

is being performed. If your organization has Lockout/Tag out policies, make sure to 

implement them before servicing the Cool Boss.

 

 

WARNING

 

Rotating Fan Blades can cause serious injury! Keep hands and loose clothing clear! 

 

WARNING

 

Disconnect the Power Cord when cleaning the Cool Boss and exercise care to 
avoid splashing water on the Motor or internal electronics. 

To maintain the Cool Boss

 

Daily

Turn off the Cooling Pump and run the Fan to dry the Media and inhibit the growth of 

bacteria, mold and mildew. Typically Media drying can take 15 to 60 minutes depending on current 
temperature and humidity.

 

 

Weekly

.

 

Change the Cool Boss Reservoir water when it gets dirty

. Dirt and other pollutants from the 

environment will get into the water and Reservoir. Cool Boss recommends draining and cleaning 

the Reservoir weekly or more often depending on the frequency of use and the cleanliness of the 

environment. 

 

CAUTION

 

Exercise care when removing the 
Drain Plug on the bottom of the 

Reservoir. There is a sealing O-Ring 

on this plug that may stick to the 
Housing and later fall to the ground 

and possibly become lost. See figure 

to the right. 

 

Weekly

.

 

Drain and clean the Cool Boss Water Reservoir. Dirt

 and other pollutants from the 

environment can settle in the Water Reservoir. Regular cleaning can remove these contaminants 

and reduce the build-up of minerals.  

 

Monthly

. Check the GFCI function monthly. 

Test the GFCI on the Cool Boss Power Cord once a 

month to ensure it is working and protecting you from electric shock.  

 

Monthly

. Clean the outside of the unit. 

Use no harsh chemicals. Unplug the Cool Boss and wipe 

down the outside of the unit with a damp cloth. The frequency of use and the cleanliness of the 

environment will affect the frequency of cleaning required.  

 

WARNING

 

Do not spray the Cool Boss with water. The electronics are not sealed. Water can 
damage the motor and/or other parts of the electrical system. 

 

Monthly

Empty the Reservoir and clean it.  

 

Monthly

Remove the Media and clean as detailed below. Dirt and other pollutants from the 

environment will become caught in the Media. Clean it regularly to keep the air fresh and clean.  

 

WARNING

 

Do not operate your Cooler if you find maintenance issues; instead, remove it from 
service. Assistance with your Evaporative Cooler is available from your dealer, by calling 
Cool Boss at 

(805) 933-9970

, or by emailing 

[email protected]

. You may 

also contact Cool Boss for parts replacement (please have the serial and model 
numbers of your unit available). 

Содержание CB-12SL





































Отзывы: