background image

2241A Distribution Panel

INSTALLATION

  Section 2

2 - 6

2-5-3. Use four screws in the mounting ears on the
panel to secure the 2241A in an equipment cabinet or
rack.

2-5-3 SIGNAL AND POWER CONNECTIONS

. All

Audio, PTT, and Power Leads connect to the rear panel
of the 2241A.

Audio Inputs.

 Connect up to 8 Audio Inputs to the

AUDIO INPUT Connector on the far right of the rear
panel. Refer to the 2241A Block Diagram on Page 2-5
for pin assignments.

Audio Sum Inputs.

 Connect up to 8 Audio Sum Inputs

to the AUDIO INPUT Connector on the far right of the
rear panel. Refer to the 2241A Block Diagram on Page
2-5 for pin assignments.

Audio Output

. Connect up to 24 Audio Outputs to the

AUDIO OUTPUT Connector on the rear panel. Refer to
the 2241A Block Diagram on Page 2-5 for pin
assignments.

PTT Inputs.

 Connect the PTT Inputs to the PTT INPUT

Connector on the rear panel. Refer to the 2241A Block
Diagram on Page 2-5 for pin assignments.

PTT Outputs.

 Connect the PTT Outputs to the PTT

OUTPUT Connector on the rear panel. Refer to the
2241A Block Diagram on Page 2-5 for pin assignments.

Power Leads.

 For 

DC Units

, check the polarity of the

power leads, then turn the DC Power Supply OFF and
connect the power leads to the terminal block on the far
left of the rear panel. Turn the DC Power Supply ON,
and check that both LEDs on the front of the 2241A are
lit.

AC Units

 have an integral power cord. If necessary,

change the plug on the AC Power cord to accommodate
local power mains receptacles.

2-5-4 SYSTEM TESTING

 This section is very general in

order to accommodate a variety of situations. Set all of
the front panel switches to the 

NORM

 Position.

Audio Distribution.

 Check that individual audio signals

are being distributed to the proper points, and check that
each output is the proper level. 

Assuming that the Front

Panel Gain Controls have not been adjusted

, the 2241A

has 0 dB gain when being driven with a 600 Ohm
Source, and with the outputs terminated with 600 Ohms.

SUM Audio Distribution.

 Check that individual sum

audio signals are being distributed to the proper points.

PTT Distribution.

 Check that individual leads are being

distributed to the proper points. Check that each PTT
Output is being properly keyed from the dispatch
console.

PTT Override

. Check that the front panel switches on

the 2241A provide override control of each transmitter.

In the 

KEY 

Position the transmitter should Key

independent of the status of the dispatch console and
the switch bat should light up 

RED

.

In the 

DISABLE

 Position, the transmitter should remain

Idle independent of the status of the dispatch console,
and the switch bat should light up 

RED

.

Set all of the front panel switches to the 

NORM

 Position,

and verify that all transmitters are tracking key
commands issued by the dispatch console. Note that the
switch bats light up 

GREEN

 when PTT is asserted from

the console.

2-6 SUPPORT

  We invite your comments, questions or

technical support requirements. 

Please

 

check our

website for the current address and phone numbers.

www.ConvexCorp.com

               e-mail:    [email protected]

Phone  703-433-9901     /    FAX  703-433-9904

If repair work is required, ship the product to the factory:

CONVEX CORPORATION

1319 Shepard Drive

Sterling, VA 20164  USA

(

Check

  www.ConvexCorp.com  

for current information.

)

Include a note:

Trouble description
Your name / phone number
Return shipping address

2-7   WARRANTY

  All Convex products are warranted

to be free of manufacturing defects for a period of one
year from the date of shipment.

2-8  PRODUCT REPAIR SERVICE

  Post warranty

repair service is available for Convex products. Convex
will advise as to the nature and cost of repair and,
subject to customer instructions, will promptly repair and
return the product.

UP TO 24 PTT OUTPUTS

UP TO 24 Tx OUTPUTS

UP TO 8 SUM INPUTS

UP TO 8 Tx INPUTS

UP TO 24 PTT INPUTS

VOTER

Rx AUDIO 

M LEAD / PTT 

2241A AUDIO / PTT DISTRIBUTION PANEL

BU

MAIN

CONVEX 2241A AUDIO / PTT DISTRIBUTION PANEL

17

13

14

15

16

18

19

20

21

22

23

24

12

11

10

9

8

7

6

5

4

3

2

1

DISABLE

KEY

PTT

NORM

POWER

M LEAD / PTT 

T1 MUX

DISPATCH CONSOLE

LOCAL RADIOS

TO REMOTE RADIOS

Tx AUDIO

Tx AUDIO

PTT

PTT

Tx

Tx

Содержание 2241A















Отзывы: