Traceable
®
is a registered trademark of Control Company
©
2008 Control Company. 92-4000-01 Rev. 3 051908
DISPLAY WARNINGS
“LLL”
Displayed when the temperature being measured is below the range of the unit
or when there is an open probe or no probe.
“HHH”
Displayed when the temperature being measured is above the range of the
unit or when there is a shorted probe.
“BAT”
Displayed when the battery is low and needs to be replaced. See Battery
section for battery replacement instructions.
RECEPTACLES
The receptacle on the right side of the unit (9, fig. 1) is for the probe. The upper left
side receptacle (10, fig.) is for an AC Adaptor. The lower left side receptacle is for the
serial data cable for the Data Acquisition System (11, fig. 1).
DATA ACQUISITION SOFTWARE
The enclosed disk is the software program for data acquisition. On the disk is the data
acquisition program and a demo program. The program can be installed and the
demo. For instructions on use, print out the READ ME file on the disk. Windows
®
is
required. In order to use the actual data acquisition program the
Accessory Data
Cable Cat No. 4235
is required. See Accessories section for ordering information.
BATTERY
If the letters “BAT” appear on the display, it indicates the batteries are low and need to
be replaced. To replace the battery, slide the battery cover located on the back of the
unit away from the unit. Remove the old battery and replace it with a new 9-Volt
alkaline battery. Use an alkaline battery, NOT a regular or heavy duty battery. Properly
connect the battery. Replace the battery cover. Incorrectly installed batteries may
damage electronics.
Turn the ON/OFF key (2, fig. 1) to the “OFF” position when the thermometer is not in
use to prolong battery life.
ALL OPERATIONAL DIFFICULTIES
If this thermometer does not function property for any reason please replace the
battery with a new 9-Volt alkaline battery Battery section, above). Low battery power
can occasionally cause any number of “apparent” operational difficulties. Replacing
the battery with a new fresh battery will solve most difficulties.
ACCESSORIES
Cat. No. 4021 Accessory Micro Probe for Cat. No. 4000
Stainless steel, 0.04” diameter, 5½” overall length, 5½’ cable length.
Cat. No. 4022 Accessory Surface Probe
Measures surface temperatures. 5¾” overall length, 6’ cable length.
Cat. No. 4023 Accessory Air Probe
Measures air temperatures only. 6¼” overall length, 6’ cable length.
Cat. No. 4001 Replacement probe for Cat. No. 4000
Stainless steel, ⅛“ diameter, 8¼” overall length, 5¼’ cable length.
Cat. No. 4005 Traceable
®
Digital Thermometer for YSI Series 400 probes
Identical to Cat. No. 4000 thermometer but accepts only YSI series 400 probes.
Supplied without probe.
Cat. No. 4006 Traceable
®
Digital Thermometer for YSI Series 400 probes
Identical to Cat. No. 4000 thermometer but accepts only YS1 series 400 probes/
Supplied with YSI-401 General Purpose probe.
Cat. No. 4002 Padded Nylon Carrying Case
For use with 4000, 4005, and 4006.
Cat. No. 4236 AC Adaptor
Accessory for use with 4000, 4005, and 4006; allows for continuous AC operation.
Cat. No. 4235 Data Acquisition System
Accessory Complete Data Acquisition System captures, displays, and stores readings
in Windows
®
. Data can be read as or imported into databases, spreadsheets, word
processors, and statistical programs. Includes the latest version of the program on disk
and 36” serial cable that plugs into instrument and computer serial port.
Cat. No.
4000 Traceable
®
Digital Thermometer
4005 Traceable
®
Digital Thermometer for YSI Series 400 probes
(Supplied
without probe)
4006 Traceable
®
Digital Thermometer for YSI Series
400 probes
(Supplied
with YSI general purpose probe)
WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-
Certified by DNV and ISO 17025 accredited
as a Calibration Laboratory by A2LA.
