Continental Disc Corporation GROTH CORPORATION 1660A Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 16

Continental Disc Corporation GROTH CORPORATION 1660A Series Скачать руководство пользователя страница 10

Page 10 of 16

recheck the film seat gap. Remove this sub-
assembly and store on a clean surface.

O-RING SEAT PALLET

Remove  the  retaining  ring  [28],  the  retainer
plate [30] and two O-Rings [29 & 31].  Inspect
and  clean  the  O-Ring  groove  and  the  bore  in
the  pallet.    Install  new  O-Rings,  and  replace
the  retainer  plate  [30]  and  retaining  ring  [28].

Do not expand the retaining ring
excessively.

Figure 5: O-Ring Pallet Assembly

BODY SEAT INSERT

The  seating  surface  is  a  thin  stainless  steel
insert [27] bonded into the body.  The flat top
surface  contacts  the  O-Ring  in  the  standard
pallet  assembly.    The  corner  radius  contacts
the  tensioned  film  of  the  optional  pallet
assembly.

Inspect the appropriate surface to be sure it is
clean, smooth and flat. Press and twist the
insert manually to verify that it firmly bonded
into the body.

If the O-Ring pallet is used, the flat sealing
surface of the insert may be lapped, using a
flat lapping block.

If  the  film  pallet  is  used,  the  sealing  radius
may  be  hand  polished,  very  carefully.    The
radius  must  be  uniform  and  not  exceeding
.030

”.

ASSEMBLY

Model  1660A:  This  model  has  one  support
plate riveted [3] to the spindle cap.  Screw the
jam  nut  [47]  onto  the  spindle  rod  [13]  and
screw the rod  into the spindle cap [22] until it
is  flush  with  the  top  surface  of  the  support
plate [4].  Then tighten the jam nut securely.

Figure 6: Spindle Assembly-Model 1660A

Models

1661A+1662A:

The

actuator

diaphragm  is  mounted  between  the  upper
(vacuum)  [4.1]  support  plate  and  the  lower
(pressure)  [4]  support  plate.    Thread  the
spindle rod [13] through the upper spindle cap
[22].

Temporarily seat the spindle tube against the
cap and adjust the rod until it extends 3/16

”

beyond the lower end of the tube. Remove
the tube and install the O-Ring [48], pressure
support

plate

[4],

diaphragm

[15],

Fluoropolymer washer [50], vacuum support
plate [4.1], and flat washer [49]. Install the
jam nut [47] and tighten securely.

Figure 7: Spindle Assembly-Model 1661A-62

«
...
8
9
10
11
12
...
»

Содержание GROTH CORPORATION 1660A Series

















Отзывы:

Нет отзывов