Contex SD 3600 series Скачать руководство пользователя страница 73

Страница: 73 / 85

D-5

Appendix D --- Error codes

Error code

100-50234

Keypad

Error code

None

Level

User

Correctable

Description

Scanner is in safemode. Please reboot scanner or

download new firmware

Potential failed comp.

User, SUx

Corrective Action.

■

User interaction.

■

Main controller board (SUx).

Error code

100-50237

Keypad

Error code

ERR_GENERAL (3)

Level

User

Correctable

Description

Host PC does not support SSE2 calculations

Potential failed comp.

User

Corrective Action.

■

User interaction.

Error code

100-20088

Keypad

Error code

ERR_GENERAL (3)

Level

Support

Correctable

Description

Motor system error, motor movement not detected.

Potential failed comp.

Mech, SUx, Cable, Motor

Corrective Action.

Error code

100-50259

Keypad

Error code

ERR_SU (12)

Level

Support

Correctable

Description

Firmware unable to identify SU-board id.

Potential failed comp.

SUx

Corrective Action.

■

Main controller board (SUx).

Error code

100-50260

Keypad

Error code

ERR_SU (12)

Level

Support

Correctable

Description

Firmware unable to identify SU-board variant.

Potential failed comp.

SUx

Corrective Action.

■

Main controller board (SUx).

Error code

100-50600

Keypad

Error code

ERR_SU (12)

Level

Support

Correctable

Description

SUx, Main controller board error

Potential failed comp.

SUx, SMPS

Corrective Action.

■

Main controller board (SUx).

■

Switch Mode Power Supply (SMPS)

Error code

100-50601

Keypad

Error code

ERR_CB (13)

Level

Support

Correctable

Description

CIS unit error

Potential failed comp.

CIS, SUx

Corrective Action.

■

CIS Unit (CIS).

■

Main controller board (SUx).

Error code

100-50602

Keypad

Error code

ERR_GENERAL (3)

Level

User

Correctable

Description

Firmware error. Please download latest firmware.

Potential failed comp.

Firmware, SUx

Corrective Action.

■

Firmware.

■

Main controller board (SUx).

Error code

100-50603

Keypad

Error code

ERR_GENERAL (3)

Level

User

Correctable

Description

Unrecoverable scanner state. Please reboot the scanner.

Download of the latest firmware and PC application/driver

may

required.

Potential failed comp.

Reboot, Firmware, Software

Corrective Action.

■

Reboot scanner.

■

Firmware.

■

PC driver/software.

Содержание SD 3600 series






















































































Результаты поиска

Содержание SD 3600 series

Отзывы:

Похожие инструкции для SD 3600 series

Бренды по названию

Популярные бренды

Contex SD 3600 series, Техническое обслуживание руководство

Результаты поиска

Содержание SD 3600 series

Отзывы:

Похожие инструкции для SD 3600 series

Бренды по названию

Популярные бренды