FSG/MTM/002 060511
27
4. CCD Camera
In the XL 42 scanners a new camera design has been used. The new camera differs mostly in
the way the basic vertical position (camera tilt) is set/adjusted.
As on the old cameras the vertical position is adjusted by turning the Vertical Adjustment
Screw (located under the camera housing) which tilts the camera. But where the old cameras
has a “finger wheel” fixed to the screw, the screw on the new cameras must be turned using a
special spanner. As it can be seen in Fig. 4-1 page 28 the spanner is the one end of the upper
half of the Vertical Alignment Arm.
Even when the Vertical Alignment Arm is not fixed to the Vertical Adjustment Screw the
camera tilt will change slightly when turning the Vertical Alignment Arm. Because of this the
Vertical Alignment Arm has to be installed and set to its initial position when adjusting the
vertical position of the camera. As this rules out using the upper half of the Vertical
Alignment Arm of the camera which is adjusted, this part is attached to the spindle console of
the fixed camera (camera B). The sole purpose of this part is to be used when adjusting the
camera tilt.
Normally there is no need to change the factory set basic vertical position of the cameras nor
to change the position of the Vertical Alignment Arm. But if it happens that the Vertical
Alignment Arm is close to one of the outer positions and needs to be returned to its initial
position or if a camera needs to be tilted, proceed as described below.
4.1 Setting the Initial Position of the Vertical Alignment Arm
Important: If the initial position of the Vertical Alignment Arm needs to be set this is most
likely because the arm is not fixed properly to the Vertical Adjustment Screw or because the
vertical position of the fixed camera has changed significantly. The vertical position of the
cameras should therefore be checked/adjusted at the same time.
Refer to Fig. 4-1 page 28).
•
Loosen the lock screw for the Vertical Alignment Arm (located under the camera housing
opposite to the Vertical Alignment Arm)
•
Loosen (and just loosen) the assembly screw for the Vertical Alignment Arm
•
Push the lower half of the arm forward (1) until the assembly screw is free of the upper
half of the arm and then swing the upper half upwards (2)
•
Detach the upper half of the arm from the Spindle Nut (3) and let the lower part swing
backwards
•
Rotate the Spindle Nut to position it in the center of the motor spindle
•
Attach the upper half of the Vertical Alignment Arm using the reverse order of the above
description
•
Tighten the assembly screw for the Vertical Alignment Arm
•
Tighten the lock screw for the Vertical Alignment Arm
4.2 Adjusting the Camera Tilt
If the correct vertical position during camera adjustment can not be obtained by means of the
tilt levers (see FSG/MTM/001 section 4.2.7) the camera tilt must be changed as described
below.
Important: Before adjusting the camera tilt set the Vertical Alignment Arm to its initial
position as described above.
•
Loosen the lock screw for the Vertical Alignment Arm (located under the camera housing
opposite to the Vertical Alignment Arm)
Содержание CHAMELEON 25
