7. Programming Your TV / VCR Combination
1. Turn on your TV / VCR combination device and
set it to its TV mode.
2. Program your remote to operate the TV functions.
Using the Code Entry Programming method
described in Section 5, find a TV Setup Code that
operates the TV functions (Power, Vol
S
/
T
, Mute,
Ch
S
/
T
, 0-9) of your TV / VCR unit.
3. Set your combination device to its VCR mode and
install a VHS tape.
4. Program your remote to operate the VCR
functions. Using the Code Entry Programming
method described in Section 5, enter, lock and
test each 3-digit VCR Setup Code for your brand
until a code is found that operates the transport
functions (PLAY, STOP, REW, FWD, PAUSE,
REC) of your TV / VCR unit.
Before you can test for the correct VCR setup
code, you must first press the [VCR] button first to
put the remote in its VCR mode.
8. Programming Your TV / DVD or TV / VCR / DVD
Combination
1. Turn on your TV / DVD combination device and
set it to its TV mode.
2. Program your remote to operate the TV functions.
Using the Code Entry Programming method
described in Section 5, find a TV Setup Code that
operates the TV functions (Power, Vol
S
/
T
, Mute,
Ch
S
/
T
, 0-9) of your TV / DVD unit.
3. Set your combination device to its DVD mode and
install a DVD.
4. Program your remote to operate the DVD
functions. Using the Code Entry Programming
method described in Section 5, enter, lock and
test each 3-digit DVD Setup Code for your brand
until a code is found that operates the transport
functions (PLAY, STOP, REW, FWD, PAUSE,
REC) of your TV / DVD unit.
Before you can test for the correct DVD setup
code, you must first press the [DVD] button to put
the remote in its DVD mode.
5. Last, if you have a TV / VCR / DVD combination
unit, you need to program your remote to operate
the VCR functions.
7. Set your combination device to its VCR mode and
install a VHS tape.
8. Using the Code Entry Programming method
described in Section 5, enter, lock and test each
3-digit VCR Setup Code for your brand until a
code is found that operates the VCR transport
functions (PLAY, STOP, REW, FWD, PAUSE,
REC) of your TV / DVD / VCR unit.
Before you can test for the correct VCR setup
code, you must first press the [VCR] button first to
put the remote in its VCR mode.
9. Code Number Readback
To identify the 3-digit TV setup codes stored under
the Point and Press
®
programming method, follow
these steps using the remote control keypad…
1. In this order, press and hold the [ENTER] button,
then the [TV] button. Hold both buttons down
together until the [TV] button illuminates. Release
both buttons as soon as the [TV] button
illuminates.
2. Press [INFO]. The mode buttons will “blink back”
the code numbers, with a 1-second interval
between each digit of the code. Please note that
for the numeric “0”, the mode buttons will
illuminate blink in fast-sequence.
Example: For code “130”, the remote will blink 1
time, then 3 times, then in a fast-sequence for the
0.
To identify the 3-digit SAT code, press [ENTER], then
[SAT]
as defined in step 1 above
, then press [INFO].
To identify the 3-digit DVD code, press [ENTER], then
[DVD]
as defined in step 1 above
, then press [INFO].
To identify the 3-digit AUDIO code, press [ENTER],
then [AUDIO]
as defined in step 1 above
, then press
[INFO].
To identify the 3-digit AUX code, press [ENTER], then
[AUX]
as defined in step 1above
, then press [INFO].
10. Master Power
Your remote has a Master Power feature that can be
programmed so that a single press of the [POWER]
button (in remote’s SAT mode) can turn all of your
electronic devices on / off together.
To program the Master Power feature, follow these
steps using the remote control keypad:
1. In this order, press and hold the [ENTER] button,
then the [POWER] button. Hold both buttons
down together until the [SAT] button illuminates.
Release both buttons as soon as the [SAT] button
illuminates.
2. Press [1]. The [SAT] button will blink 3-times and
go out.
To use the Master Power feature, follow these steps:
1. Press [SAT] to select the remote’s SAT mode.
2. Press [POWER] – the remote will turn on / off your
SAT, TV, DVD, AUDIO an AUX devices with one
button press.
To reset the Master Power feature to its default
setting, follow these steps using the remote control
keypad:
1. In this order, press and hold the [ENTER] button,
then the [POWER] button. Hold both buttons
down together until the [SAT] button illuminates.
Release both buttons as soon as the [SAT] button
illuminates.
2. Press [0]. The [SAT] button will blink 3-times and
go out.
