Contec AD16-64(LPCI)LA страница 28 Скачать руководство пользователя

Страница: 28 / 83

2. Setup

AD16-64(LPCI)LA

Step 5 Checking Operations with

the Diagnosis Program

Use the diagnosis program to check that the board and driver software work normally, thereby you can
confirm that they have been set up correctly.

What is the Diagnosis Program?

The diagnosis program diagnoses the states of the board and driver software.

It can also be used as a simple checker when an external device is actually connected.

Using the “Diagnosis Report” feature reports the driver settings, the presence or absence of the board,
I/O status, and interrupt status.

Check Method

To check the analog input data, connect to an external signal source.
The figure below shows an example of checking by connecting to an external signal.
The example below is for analog input channel 0 on the AD16-64(LPCI)LA.

Wiring Diagram

< Analog input >

Figure 2.4. Wiring Diagram

Input data remains indeterminate when no input pin is connected. The input pin for the channel

not connected to the signal source must be connected to the analog ground.
For details, see “Chapter 3 External Connection”.

Analog Ground (CNA)

37pin

CH0 [-](CNA)

38pin

- Single-Ended Input

- Differential Input

Interface connector

Signal source

(e.g. Battery etc.)

Analog Ground (CNA)

3pin

CH0 (CNA)

4pin

CH0 [+](CNA)

4pin

Signal source

(e.g. Battery etc.)

CAUTION

Содержание AD16-64(LPCI)LA




















































































Результаты поиска

Содержание AD16-64(LPCI)LA

Отзывы:

Похожие инструкции для AD16-64(LPCI)LA

Бренды по названию

Популярные бренды

Contec AD16-64(LPCI)LA, Руководство пользователя

Результаты поиска

Содержание AD16-64(LPCI)LA

Отзывы:

Похожие инструкции для AD16-64(LPCI)LA

Бренды по названию

Популярные бренды