Contec AD16-64(LPCI)LA страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 83

background image

1. Before Using the Product

6

AD16-64(LPCI)LA

Handling Precautions

Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in
an explosion, fire, electric shock, or failure.

-

There are switches and jumpers on the board that need to be set in advance. Be sure to check these
before installing the board.

-

Only set the switches and jumpers on the board to the specified settings.
Otherwise, the board may malfunction, overheat, or cause a failure.

-

Do not strike or bend the board.
Otherwise, the board may malfunction, overheat, cause a failure or breakage.

-

Do not touch the board's metal plated terminals (edge connector) with your hands.

Otherwise, the board may malfunction, overheat, or cause a failure.
If the terminals are touched by someone's hands, clean the terminals with industrial alcohol.

-

Do not plug or unplug the cables which are connected to the board while the PC or expansion unit is

still turned on.

Otherwise, the board may malfunction, overheat, or cause a failure.

Be sure that the personal computer power is turned off.

-

Do not install or remove the board to or from the slot while the computer's power is turned on.

Otherwise, the board may malfunction, overheat, or cause a failure.
Be sure that the personal computer or the I/O expansion unit power is turned off.

-

Make sure that your PC or expansion unit can supply ample power to all the boards installed.
Insufficiently energized boards could malfunction, overheat, or cause a failure.

-

The specifications of this product are subject to change without notice for enhancement and quality

improvement.
Even when using the product continuously, be sure to read the manual and understand the contents.

-

Do not modify the product. CONTEC will bear no responsibility for any problems, etc., resulting
from modifying this product.

-

Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever

(including damages for loss of business profits) arising out of the use or inability to use this
CONTEC product or the information contained herein.

-

Regarding “CE EMC Directive Notice”.
Please connect the Interface Connector with a shielded cable to meet the mentioned standard above.

DANGER

CAUTION

«
...
11
12
13
14
15
...
»

Содержание AD16-64(LPCI)LA




















































































Отзывы:

Нет отзывов

Похожие инструкции для AD16-64(LPCI)LA

FlashMover 8-in-1 USB

Бренд: Microdia Страницы: 4

Бренд: StarTech.com Страницы: 2

Бренд: X-media Страницы: 8

Бренд: Sunrich Tech Страницы: 11

Бренд: Icy Box Страницы: 20

Бренд: S2Konnect Страницы: 24

Smart Connector

Бренд: KUARIO Страницы: 20

Бренд: IBM Страницы: 56

Бренд: Anker Страницы: 14

Бренд: Hama Страницы: 24

Бренд: Hama Страницы: 28

Бренд: IEI Technology Страницы: 141

Бренд: PNY Страницы: 2

Radeon X1650AGP256

Бренд: Diamond Multimedia Страницы: 1

Бренд: Rosslare Страницы: 25

Бренд: Diablotek Страницы: 1

Бренд: Glancetron Страницы: 10

Бренд: ZyXEL Communications Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды