4
Issue 01
Remove the CRX2’s battery cover and insert 4 new high
quality alkaline AAA batteries.
Warning: Consort is not responsible for damage due to
corrosion. Battery leakage will cause permanent damage.
Do not use batteries when unit is powered on with mains.
To help avoid battery leak:
Replace the batteries annually, even if there is not a
low battery warning. Remove failing or flat batteries
immediately.
Always fit a pair of new high quality alkaline batteries
from the same pack. Never mix new and old batteries,
or batteries of different brands or types.
Never attempt to revive alkaline batteries by heating,
crushing or recharging.
Note: The clock has to be set after replacing the batteries, or
if the USB power cable has been removed from the CRX2.
This does not apply if it is being used with the MRX1 Multizone
controller.
20. Batteries
21. Power adapter for fixed installation
The CRX2 controller is supplied with a power adapter that will
fit a 35mm or a 25mm metal or dry lining back box. The
power adapter should only be connected to a wiring
protected by a 6A fuse or 6A circuit breaker. Connect line
and neutral conductors to the terminal block. Please note
that the adaptor supplied with the controller must be
installed exactly as the figures show, otherwise the USB
connector will not fit correctly. The centre of the back box
must be kept clear to allow room for the USB connector.
When fitting the wall bracket, ensure that the adaptor is
installed properly and feed the cable through the centre of
the bracket. Screw the bracket to a back box taking care
not to damage the power adaptor or leads by long screws.
Connect the USB cable into the power port at back of the
controller as shown on the photo. Check that the CRX2 is
working. Attach top of the CRX2 to the wall bracket and
slowly tilt it to place observing that the USB connector is
moving in to the opening freely. Once the controller is in
place secure the two screws on the bottom of the controller.
Please note that the controller screen will take up to
one minute to display after powering up for the FIRST
time.
22. Power adapter for fixed installation (cont’d)
Customer Helpline
Should you need any advice on the use of you new Consort product,
or should you require service or repair, please contact our Helpline:
Tel: 01646 692172 Fax: 01646 695195
Email: [email protected]
The CRX2 is guaranteed for one year against faulty material or
workmanship. This applies only if the appliance has been used for
purposes in accordance with the instructions provided and has not
been misused, neglected, damaged, modified or repaired by any
person not authorised by us. This guarantee is offered to you as an
extra benefit and does not affect your legal rights.
Consort Equipment Products Ltd.
Registered Office: Thornton Industrial Estate, Milford Haven,
Pembrokeshire, SA73 2RT
Tel: 01646 692172 | Fax: 01646 695195
[email protected] | [email protected]
BS EN ISO 9001 Registered Company No FM12671
Reasonable care has been taken to ensure that this guide is
accurate at the time of printing. In the interest of progress, the
Company reserve the right to vary specifications from time to time
without notice.
23. Setup menu
1.
Touch and hold and icons together for 10
seconds.
2.
The CRX2 will enter the setup menu.
3.
Use and to change a value.
4.
Use to scroll between the settings.
01 – temperature calibration
The temperature reading has been factory calibrated but if
for any reason it needs adjusting (better accuracy required,
to suit different position in the room etc.), the reading can be
recalibrated in 0.5 degrees steps.
Please note that if the unit is powered by the power adapter, the
temperature reading REQUIRES recalibration. Lower the value by 1.5
degrees.
02 – change between degrees Celsius or Fahrenheit
03 – set minimum temperature
(- - - = heating OFF, 4deg = frost protection)
04 – set maximum temperature
05 - information about the software version
locking screws
USB power ports
temperature sensor
wall fixing
wall fixing
