Intended use
The product looks deceptively similar to a working wireless surveillance camera and is intended to act as a
deterrent in secluded or critical areas (e.g., gateways and entrances etc.).
The dummy camera is designed for installation and use indoors, it must not get wet or damp.
The dummy camera is powered by batteries.
Always observe the safety instructions and all other information included in these operating instructions.
This product complies with the applicable national and European requirements. All names of companies and
products are the trademarks of the respective owner. All rights reserved.
Contents
• Dummy Camera
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We do not assume any liability for any consequential damage!
Nor do we assume any liability for material and personal damage caused by improper use
or non-compliance with the safety instructions! In such cases, the warranty will be null
and void.
• The unauthorised conversion and/or modi
fi
cation of the product is not permitted for safety and
approval reasons (CE). Do not open/disassemble! Contains no customer-serviceable parts.
• The product should be used only in dry indoor areas; it must not get wet or damp.
• The product is not a toy and must be kept out of the reach of children. Install and use the
product where it is out of the reach of children.
• Do not operate the device in environments where there are high levels of dust,
fl
ammable
gases, vapours or solvents. There is a danger of
fi
re and explosion!
• Do not carelessly leave the packaging material lying around since this may become a danger-
ous toy for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental drops, even
from a low height.
General information on batteries/rechargeable batteries
• Batteries/rechargeable batteries must be kept out of the reach of children.
• Do not leave batteries/rechargeable batteries lying around; they could be swallowed by children or pets. If
swallowed, consult a doctor immediately.
• Leaking, or damaged batteries/rechargeable batteries, in contact with the skin can cause acid burns,
therefore, use suitable protective gloves.
• Batteries/rechargeable batteries must not be short-circuited, opened or thrown into a
fi
re. There is a risk of
explosion!
• Do not recharge normal, non-rechargeable batteries, risk of explosion! Only charge rechargeable batteries
that are intended for this purpose; use a suitable battery charger.
• Never mix standard batteries with rechargeable batteries, use either standard batteries or rechargeable
batteries.
• Do not mix batteries/rechargeable batteries with different charge levels (e. g. full and half-full batteries/
rechargeable batteries).
• Always replace the complete set of batteries/rechargeable batteries.
• Check that the polarity is correct, when inserting the batteries/rechargeable batteries (pay attention to
plus/+ and minus/-).
• If you wish to use rechargeable batteries please note that, due to the lower output voltage (batteries =
1.5 V, rechargeable batteries =1.2 V), the operating time will decrease. Therefore, we recommend that you
use high-quality alkaline batteries to ensure long-lasting and reliable operation.
Installation
Move the camera head by hand very carefully, otherwise the drive could be damaged.
• First, choose a suitable location to mount the dummy camera.
• Screw the dummy camera
fi
rmly to the wall. Depending on the wall, use suitable screws and wall plugs.
Please make sure that existing cables or wiring not damaged when drilling/screwing into place.
• If the enclosed dummy WLAN antenna is to be attached, insert it into the corresponding opening on the
rear of the dummy camera.
• Adjust the tilt of the dummy camera as desired, so it points roughly at the area to be monitored.
To adjust, loosen the round locking screw at the rear (turn anticlockwise). The dummy camera can then be
aligned. Tighten the locking screw again, but do not apply force, do not use tools!
Inserting/replacing the batteries
• Open the battery compartment on the top and insert three AA batteries (mignon), paying attention to the
correct polarity (plus/+ and minus/-).
• Close the battery compartment again.
• The batteries need to be replaced, if the camera motor stops moving.
Operation
• Switch the dummy camera on using the ON/OFF switch on the back (“ON”, “OFF”).
• The brightness sensor on the front of the dummy camera detects changes in brightness in the monitored
area, and activates the dummy camera’s drive motor to create the impression the area is under surveil-
lance. A red LED
fl
ashes at the same time.
• After about 20 seconds, the motor and the LED are switched off.
• If the motor drive, or the
fl
ashing LED is not required, switch the dummy camera off and remove the
batteries from the battery compartment.
Maintenance and Cleaning
Maintenance or repairs may only be performed by quali
fi
ed personnel or a specialised repair shop. The
product contains no parts that require servicing. Therefore, do not open/dismantle it (except to replace the
batteries).
Use a clean, dry, soft cloth for cleaning. Do not apply too much pressure on the case, this could cause
scratch marks.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since these
could damage the housing or even impair operation.
Disposal
a) General instructions
Please dispose of the device when it is no longer of use, according to the current statutory
requirements.
b) Batteries and Rechargeable Batteries
As the end user, you are required by law (Battery Ordinance) to return all used batteries/rechargeable bat-
teries; disposal of them in the household waste is prohibited!
Contaminated batteries/rechargeable batteries are labelled with these symbols to indicate that
disposal in the domestic waste is forbidden. The designations for the heavy metals involved are:
Cd = Cadmium, Hg = Mercury, Pb = Lead.
You can return used batteries/rechargeable batteries and button cells free of charge to any authorised
disposal station in your area, to our stores or to any other store where batteries/storage batteries/button
cells are sold.
You thereby ful
fi
l your statutory obligations and contribute to the protection of the environment.
Technical Data
Power supply ...............................3 batteries of type AA/Mignon
Power consumption .....................max. 100 mA (motor and LED activated), standby approx. 0.2 mA
Motor panning range ...................approx. 45°
Dimensions ..................................70 x 230 x 182 mm (W x D x H, incl. wall bracket)
Weight .........................................approx. 205 g (without batteries)
O P E R A T I N G I N S T R U C T I O N S www.conrad.com
WLAN Dummy Camera with Motor
Item no. 75 43 64
Version 09/12
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, micro
fi
lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.
