3
Operating Instructions
Wardrobe Light with IR Sensor
Item no: 2380482
1 Intended use
The product is a cabinet light and features 3 operating modes:
■
Manual mode:
the light is manually switched on and off.
■
Sensor mode:
the light is off when the sensor is covered. The light is on when the sensor
is unobstructed.
■
Sensor timer mode:
the light switches on for a set period when the sensor detects move-
ment.
The product is intended to be permanently installed.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be dam-
aged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product
available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights
reserved.
2 Delivery contents
■
Product
■
2x Bracket
■
2x Wall plug and screw
■
2x Adhesive tape
■
Operating instructions
3 Latest product information
Download the latest product information at
www.conrad.com/downloads
or scan the QR
code shown. Follow the instructions on the website.
4 Description of symbols
The symbol with the exclamation mark in the triangle is used to indicate important
information in this document. Always read this information carefully.
This product is constructed according to protection class III.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
5.1 General
■
The product is not a toy. Keep it out of the reach of children and pets.
■
Do not leave packaging material lying around carelessly. This may become dangerous
playing material for children.
■
If you have questions which remain unanswered by this information product, contact our
technical support service or other technical personnel.
5.2 Handling
■
If it is no longer possible to operate the product safely, take it out of operation and pro-
tect it from any accidental use. Safe operation can no longer be guaranteed if the
product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
■
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
■
Consult an expert when in doubt about the operation, safety or connection of the appli-
ance.
5.3 Operating environment
■
Do not place the product under any mechanical stress.
■
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam
and solvents.
■
Protect the product from high humidity and moisture.
■
Protect the product from direct sunlight.
5.4 Batteries
■
Correct polarity must be observed while inserting batteries.
■
The batteries should be removed from the device if it is not used for a long period of time
to avoid damage through leaking. Leaking or damaged batteries might cause acid burns
when in contact with skin, therefore use suitable protective gloves to handle corrupted
batteries.
■
Batteries must be kept out of reach of children. Do not leave batteries lying around, as
there is risk, that children or pets swallow them.
■
All batteries should be replaced at the same time. Mixing old and new batteries in the
device can lead to battery leakage and device damage.
■
Batteries must not be dismantled, short-circuited or thrown into fire. Never recharge non-
rechargeable batteries. There is a risk of explosion!
5.5 LED light
■
Do not look directly into the LED light!
■
Do not look into the beam directly or with optical instruments!
6 Product overview
Sensor head
Sensor
Light
Battery compartment
Control switch
7 Getting started
7.1 Installing batteries
Note:
If an insulating strip protrudes from the battery compartment, batteries are installed
already. Pull the strip out to establish the power supply.
P
RECONDITIONS
:
a
Prepare the required number of batteries of the correct type as stated in the section
“Technical data”.
1. Slide open the battery compartment cover in the direction of the arrow and remove it.
2. Insert the batteries into the battery compartment observing the polarity markings in the
compartment.
3. Attach the compartment cover and slide is shut to close the battery compartment. If a
seal is present, make sure it sits correctly and you do not damage it when closing the
compartment.
8 Operation
8.1 Selecting operation modes
Select an operating mode suitable for your application.
The below illustration roughly explains the working of every mode.
Light on (30 s)
Light off
Sensor timer mode
max. 8 cm
Manual mode
Sensor head
Sensor
Light on OR off
Sensor mode
Light off
Light on
Object
Manual mode
In manual mode, the product is permanently on or off.
1. To switch the light on, move the control switch
D/H/ON/OFF
to
ON
.
2. To switch the light off, move the control switch
D/H/ON/OFF
to
OFF
.