Only black-and-white camera image
• At night, the camera automatically switches to a black-and-white image (at the same time, the
IR LEDs are activated). Colour is not possible in this case.
• Check the settings in the setup menu.
Image too bright/dark
• Check the settings in the setup menu; if necessary, reset the camera to the factory settings.
• Do not point the camera at the sun or a light source.
• Select suitable settings from the setup menu, e.g. for the white balance, etc.
Disposal
The product must not be disposed of in the household waste.
Please dispose of the product at the end of its service life according to the current
statutory requirements.
Technical data
Image sensor ..................................6.35 mm (1/4”), CMOS
Video signal .................................... AHD (observe the chapter “Information about AHD”)
Output level ....................................1.0 Vpp, 75 Ω
Effective resolution .........................1280 x 720, (720p) 25 frames/s
Perspective .....................................68° horizontal, 54° vertical
Video output ...................................BNC
Light sensitivity ...............................0.01 lux (F1.2) or 0 lux (IR on)
Focal length ....................................3.6 mm
White balance .................................Automatic (AWB)
Amplification ...................................Automatic (AGC)
Signal-to-noise ratio (S/N ratio) ......> 52 dB (AGC off)
Shutter speed .................................1/50 - 1/100000 s
Operating voltage ...........................12 V/DC (stabilised)
Current consumption ......................max. approx. 320 mA (IR on)
IR LEDs ..........................................1 x High-Power
IR wave length ................................850 nm
IR range ..........................................max. 12 m
IP protection class ..........................IP65
Mounting location ...........................indoors/outdoors
Operating temperature ...................-20 °C to +50 °C
Cable length ...................................approx. 0.4 m
Dimensions (Ø x H) ........................54 x 60 mm
Weight ............................................approx. 169 g (incl. cable)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical status at the time of
printing.
© Copyright 2015 by Conrad Electronic SE.
Set the correct input channel on the display device, to display the camera image.
If necessary, the camera has to be correctly oriented so you can monitor the desired field of
view.
The IR-LED is automatically activated by darkness. However, the LED is not visible to the hu-
man eye. Please bear in mind that the image on a connected monitor will not be displayed in
colour at night, but in black and white instead.
The setup menu
Please observe the manufacturer’s operating instructions for the setup menu.
If it was not provided in printed form together with the camera, you can download it
as a PDF on the internet page of the product.
a) General
The camera has an extensive setup menu. The special button used for operation is located on
the camera’s connection cable.
In the setup menu, various settings can be made, including the language for the setup menu.
From here, you can also reset the settings to the default.
To call up the setup menu, activate a submenu or confirm a setting, press the button briefly
(like a conventional button).
To select a setting function or to change a setting, the button can be moved in four directions
(see label next to the button):
“L”
Move the button to the left briefly
“R”
Move the button to the right briefly
“UP”
Move the button upward briefly
“DOWN” Move the button downward briefly
b) Setup Menu, call up/exit, save settings
To call up the setup menu, press the button briefly. The setup menu is shown in the picture of
the connected monitor.
To save all settings select function “9. EXIT”. Move the button to the left/right briefly to select
“SAVE&END”. Briefly press the button to confirm.
If the setup menu is exited without the settings being saved with “SAVE ALL”, they
will be lost if the camera is disconnected from the power supply or if there is a loss
of power!
c) Resetting the settings in the setup menu
To call up the setup menu, press the button briefly. The setup menu is shown in the picture of
the connected monitor.
To reset all settings select function “9. EXIT”. Move the button to the left/right to select “RE-
SET”. Briefly press the button to confirm.
Maintenance and cleaning
Maintenance or repair work may be performed only by qualified personnel or a specialised
repair shop. The product contains no parts that require servicing. Therefore, do not open/dis-
mantle it.
To clean the outside of the product, a dry, soft and clean cloth is sufficient. If it is very dirty, use
a cloth slightly moistened with clean water. Do not apply too much pressure on the front glass
or the housing, as this could cause scratching.
Dust can easily be removed using a clean, long-haired brush and a vacuum cleaner.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since these
could damage the housing or even impair operation.
Troubleshooting
No camera image (or only interference patterns)
• Make sure that your digital recorder can function with AHD cameras. Common digital record-
ers are not suitable!
If your digital recorder supports AHD cameras as well as common CVBS-PAL cameras, make
sure that the correct operating mode is selected.
• Set the monitor to the right input channel.
• Check the voltage/power supply to the camera.
If the cable is too long, the voltage drops in the cable; use a cable with a larger diameter, if
necessary.
• Check the camera’s cable connections.
