background image

 

 

Contents   

 

 

 

 

 

 

 

 

 

 

DFlex-4/104 User's Manual, ver. 0.04 

Table of Contents 

 

Chapter 1: Introduction

 

Introduction.................................................................................1-1 
Manual Overview........................................................................1-1 

Conventions & Symbols.....................................................1-2 

Product Overview .......................................................................1-3 

DFlex-4/104 Adapter..........................................................1-3 
DFlex-4/104 Software ........................................................1-6 

Customer Service Overview .......................................................1-6 
RMA Overview...........................................................................1-9 

 

Chapter 2: Hardware Installation

 

Introduction.................................................................................2-1 
Configuration ..............................................................................2-1 

Port Addresses....................................................................2-2 

Status Port Addresses ................................................2-3 
Custom Port Addresses..............................................2-4 

Interrupt Selection ..............................................................2-6 

Mode 1 (one IRQ)......................................................2-7 
Mode 2 (two IRQs)....................................................2-9 
Mode 3 (four IRQs) .................................................2-11 

Baud Rate Selection .........................................................2-12 
Serial Line Interface Modules (SLIM).............................2-15 

SLIM Installation.....................................................2-15 
SLIM compatibility .................................................2-18 

Installing the DFlex-4/104 Adapter in your System ........2-18 

 

Chapter 3: Software Installation 

Introduction.................................................................................3-1 
Configuration ..............................................................................3-1 

DOS 3.XX - 6.XX ..............................................................3-1 
Linux...................................................................................3-2 
Multiuser DOS 7 GOLD ....................................................3-2 
OS/2....................................................................................3-2 
QNX 2.XX..........................................................................3-2 
QNX 4.XX..........................................................................3-3 
SCO Unix ...........................................................................3-3 
Windows 3.XX...................................................................3-3 
Windows 95/98...................................................................3-3 
Windows NT ......................................................................3-4 

Utilities........................................................................................3-4 

Portfind ...............................................................................3-4 
Porttest................................................................................3-4 
SeePORT ............................................................................3-4 

Содержание DFlex-4/104



















































































Отзывы: