background image

3

Foreword

This manual contains important instructions for this machine. These instructions must be followed
during installation, operation, and maintenance of the machines.

This manual provides information and procedures to safely operate. For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions described in this
manual.

We reserves the right to change any of the contents in this manual without notice.

Warranty

Our products are covered by warranty for a period of twelve (12) months from the date of
purchase against defects in material or workmanship provided that:

The product concerned has been operated and maintained in accordance with the operating
instructions.

Has not been damaged by accident, misuse or abuse.

Has not been tampered with or repaired by any unauthorized person.

Any evidence of failure to meet these conditions may result in a denial of the warranty claim.

The owner is responsible for the cost of transportation to and from the authorized repairer and the
unit is at the owners risk while in transit to and from the repairer.

Impact damage is not covered under warranty. Clutches are not covered under any warranty.

Engines are officially guaranteed by engine manufacturer. Please refer to the annex for engine
warranty.

Содержание CR68H

















Отзывы: