Congatec conga-HPC/EVAL-Client Скачать руководство пользователя страница 42

Страница: 42 / 65

2021

congatec

GmbH

GEVAm03

42/65

4.9

Audio Interfaces

The conga-HPC/EVAL-Client features the following audio interfaces:

• Audio Jack (4-pole) on connector X49
• Connector X50 for an external I²S or SoundWire

codec

• DMIC signals on connector X48

4.9.1

Audio Jack (4-Pole)

The conga-HPC/EVAL-Client features a 4-pole audio jack (X49) for a 3.5 mm CTIA standard plug. This audio jack is connected to

an onboard

SoundWire

codec (Realtek ALC711).

Table 35 X49 - Audio Jack Pinout

Pin Jack

Signal

Description

Tip

LINE_L

Line-OUT - left channel

Ring 1

LINE_R

Line-OUT - right channel

Ring 2

A_GND

Analog ground

Sleeve

MIC

Microphone

Connector Type

X49: 3.5 mm, 4-pole CTIA standard plug

4.9.2

I²S/SoundWire

The conga-HPC/EVAL-Client features header X50 to connect a card with an external I²S or SoundWire

codec.

Table 36 X50 - I²S/SoundWire Header Pinout

Pin Signal

GND

I2S_LRCLK/SNDW_CLK3

I2S_CLK/SNDW_CLK2

I2S_DIN/SNDW_DAT2

PLTRST#

I2S_DOUT/SNDW_DAT3

Audio Jack Plug

Ring 1
Ring 2

Sleeve

Tip

X50

Содержание conga-HPC/EVAL-Client

































































Результаты поиска

Содержание conga-HPC/EVAL-Client

Отзывы:

Бренды по названию

Популярные бренды

Congatec conga-HPC/EVAL-Client, Руководство пользователя

Результаты поиска

Содержание conga-HPC/EVAL-Client

Отзывы:

Бренды по названию

Популярные бренды