Congatec 050700 Скачать руководство пользователя

Страница: 69 / 72

2022

congatec

GmbH

TSTLm01

69/72

8.2

Bootstrap Signals

Table 39 Bootstrap Signal Descriptions

Signal

Pin # Description of Bootstrap Signal

I/O

PU/PD

Comment

HDA_SDOUT

A33

High Definition Audio Serial Data Output

O 3.3 VSB

PU 1 kΩ 3.3 VSB

SPKR

B32

Output for audio enunciator, the “speaker” in PC-AT systems

O 3.3 V

PEG_LAN_RV#

D54

PCI Express Graphics lane reversal input strap. Pull low on the carrier
board to reverse lane order

I 3.3 V

PU 10 kΩ 3.3 V

SMB_ALERT#

B15

System Management Bus Alert – active low input can be used to
generate
an SMI# (System Management Interrupt) or to wake the system.

I 3.3 VSB

PU 2k2 3.3 VSB

SPI_MOSI

A95

Data out from module to carrier board SPI BIOS flash

O 3.3 VSB

PU 4k75 3.3 VSB

BIOS_DIS0#

A34

Selection strap to determine the BIOS boot device

I 3.3 VSB

PU 10 kΩ 3.3 VSB

BIOS_DIS1#

B88

Selection strap to determine the BIOS boot device

I 3.3 VSB

PU 10 kΩ 3.3 VSB

DDI1_CTRLDATA_AUX-

D16

Multiplexed with DP1_AUX- and HDMI1_CTRLDATA

PU 2k2 3.3 V

DP1_AUX-

DP AUX- function if DDI1_DDC_AUX_SEL is no connect

I/O PCIE

HDMI1_CTRLDATA

HDMI/DVI I2C CTRLDATA if DDI1_DDC_AUX_SEL is pulled high

I/O OD 3.3 V

DDI2_CTRLDATA_AUX-

C33

Multiplexed with DP2_AUX- and HDMI2_CTRLDATA

PU 2k2 3.3 V

DP2_AUX-

DP AUX- function if DDI2_DDC_AUX_SEL is no connect

I/O PCIE

HDMI2_CTRLDATA

HDMI/DVI I2C CTRLDATA if DDI2_DDC_AUX_SEL is pulled high

I/O OD 3.3 V

DDI3_CTRLDATA_AUX-

C37

Multiplexed with DP3_AUX- and HDMI3_CTRLDATA

PU 2k2 3.3 V

DP3_AUX-

DP AUX- function if DDI3_DDC_AUX_SEL is no connect

I/O PCIE

HDMI3_CTRLDATA

HDMI/DVI I2C CTRLDATA if DDI3_DDC_AUX_SEL is pulled high

I/O OD 3.3 V

Caution

1. The signals listed in the table above are used as chipset configuration straps during system reset. In this condition (during reset), they are

inputs that are pulled to the correct state by either COM Express™ internally implemented resistors or chipset internally implemented

resistors that are located on the module.

2. No external DC loads or external pull-up or pull-down resistors should change the configuration of the signals listed in the above table.

External resistors may override the internal strap states and cause the COM Express™ module to malfunction and/or cause irreparable

damage to the module.

Содержание 050700






































































Результаты поиска

Содержание 050700

Отзывы:

Похожие инструкции для 050700

Бренды по названию

Популярные бренды

Congatec 050700, Руководство пользователя

Результаты поиска

Содержание 050700

Отзывы:

Похожие инструкции для 050700

Бренды по названию

Популярные бренды