Hardware Pack
26- #10 x 1-1/4” Screw
2 - 1/4 - 20 x 3-1/4” Bolt
6 - 1/4” Washer
2 - 1/4” Nylon Nut
2 - 1/4 - 20 x 2-1/4” Bolt
2 - Hex Nut
4 - Push in Plug (white)
2 - Adjustable Braces
1 - Cable Lock Set
Tools Needed for Assembly
* - Hammer or mallet
* - Cordless Drill
* - 1/8” & 9/32” Drill bits
* - Phillips Screwdriver
* - Pliers
* - 7/16” wrench or adjustable wrench
* - Liquid soap or lubricant
* - Battery operated drill motor
Barrier Parts List
(Included in Hardware Pack)
4 -
#10 x 1-1/4” screws
1 - Strip of 4 Foam Pads
1 - Large Barrier Section
1 - Small Barrier Section
1 - Upper Brace
1 - Lower Base
Parts List
4 - Handrail / Leg
2 - Bottom Treads
8 - Upper Treads
1 - Left Tread Connector
1 - Right Tread Connector
1 - Deck Platform with
4 wedges attached
Model #7000X
ELIMINATOR A-FRAME LADDER
Ladder must be attached to pool frame -
DO NOT USE
with inflatable pools
If missing parts call - Toll free U.S./Canada - 800-635-3213 or www.conferladders.com
Safe Installation
To reduce the risk of electrocution, drowning, entrapment, falls, or other
serious injury or death:
Check building codes/permitting.
Consult your local Building Department before installation of your pool and
equipment. Pool/equipment installation must comply with the codes of the authority having jurisdiction and
may require permits (e.g., building, plumbing, electrical, zoning, etc.).
Use for intended purpose only
• Use only as a swimming pool ladder.
• This ladder is designed and manufactured for a specific pool wall height and/or deck of the pool - check
product specification and the height of your pool.
Check that you have all required parts.
Check the contents of the carton with the Parts List for this ladder.
All parts and hardware are required. If any parts are missing,
DO NOT attempt to assemble or install
the ladder.
Instead, call Toll Free U.S. - 800-635-3213 or visit our web site at www.conferladders.com for
assistance.
Select an appropriate location
- The ladder must be located on a level, solid base and in a location that will
be in full view of competent adult supervision when in use.
Follow all instructions
• For stable, correct assembly and installation, all instructions must be followed completely and in the
sequence shown.
• Follow the manufacturer’s recommendations for the safe use of all hand tools and equipment used during
installation.
Cordless drill only - no corded drills near pool.
Use a cordless drill for assembly and installation. To reduce
the risk of electrocution, NEVER use a corded drill in or around a pool.
Lift safely.
When lifting awkward or heavy loads, have another person help you.
Double check after installation
• Before using the product, after assembly and installation, go over the instructions and procedures again to
make sure nothing has been overlooked.
• Make sure that safety labels are installed and legible.
2
Fingers
IMPORTANT: Remove the wedges from the deck plat-
form protrusions and SAVE for step 5.
Slide the handrail/ legs together as shown. Apply
liquid soap or spray lubricant to aid assembly.
Twist and save.
Pliers may be
useful to aid in removal.
Step 3.
Place one handrail/leg assembly on a clean
flat surface and push the deck platform protrusions
in the opening.
Step 4.
Repeat the process with the second handrail/
leg assembly, pushing firmly onto the deck
protrusions to ensure a secure fit.
Step 8.
Step 5.
Insert the four wedges that were saved from
step 1, into the top of the openings as shown.
Insert wedges
Step 12.
Attach
Bottom
treads
Stand here
Stand here
Push down firmly.
Push down firmly.
3
2
Step 6.
Slide five upper treads into position so they
are resting on the double nubs of the legs (as
shown in the diagram). Secure the treads to
the legs using the #10 x 1-1/4” screws (two
per tread), through the pre-drilled holes.
Deck Platform
Handrail/Leg
Left Tread
Connector
Upper
Tread
Right Tread
Connector
Adjustable
Brace
(As shown
in Step #13)
Upper
Brace
Upper
Tread
Bottom
Tread
Lower Base
Large
Barrier
Small
Barrier
Tread connectors
Step 7a.
1/4” Nylon
Nut
1/4" Washer
1/4”-
20 x 3-1/4”
Bolt
Snap Small
and Large
Barrier
Sections into
slots on
Lower Base
as shown.
Separate Barrier sections at the top slightly and
position Upper Brace over Small Barrier Section.
Next, spread the “fingers” on the Upper Brace and
slide into position on the Large Barrier Section.
Step 9.
Hardware Pack
26 - #10 x 1-1/4" screw
2 - 1/4 - 20 x 3-1/4" Bolt
6 - 1/4" Washer
2 - 1/4" Nylon Nut
2 - 1/4 - 20 x 2-1/4" Bolt
2 - Hex Nut
4 - Push in Plug (white)
2 - Adjustable Braces
1 - Cable Lock Set
Tools Needed for Assembly
* - Hammer or mallet
* - Cordless Drill Motor
* - 1/8” & 9/32” Drill Bits
* - Phillips screwdriver bit
* - Pliers
* - 7/16” wrench or adjustable wrench
* - Dish liquid or spray lubricant
Barrier Parts List (if included)
(Included in Hardware Pack)
4 -
#10 x 1-1/4” screws
1 - Strip of 4 Foam Pads
1 - Large Barrier Section
1 - Small Barrier Section
1 - Upper Brace
1 - Lower Base
Model #7000X
“ELIMINATOR” A-FRAME LADDER
Adjustable to fit 48” to 54” Rigid-Framed Above Ground Pools
ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY
Parts List
4 - Handrail / Leg
2 - Bottom Treads
8 - Upper Treads
1 - Left Tread Connector
1 - Right Tread Connector
1 - Deck Platform with
4 wedges attached
If missing parts call - Toll free U.S. - 866-396-2968 or www.conferladders.com
Step 7b.
Step 10.
SWING UP INSTRUCTIONS
When not in use
ALWAYS
secure ladder by swinging
up outer treads and locking with cable lock provided.
To swing up the outer treads stand on the
bottom tread, grasp the underside of the
second lowest tread and swing it out
toward you. Swing them up until the tread
connectors drop into the preformed locks
on each leg and stay in the upright position.
To lower the treads lift them straight up to
clear the locks and carefully swing them
down toward you.
Locate
cable
lock
here
11.
Place the Base and Brace into position, centered,
on the bottom and fourth treads of the ladder.
Install the four (4) #10 x 1-1/4" screws (included in
hardware pack) on a slight angle, first in the
Upper brace, then in the Lower Base. Install the
self-adhering foam strips to the Large Barrier
Section as shown in diagram.
NOTE:
Ladder
MUST
be filled with water to prevent floating.
Winterizing: To winterize your ladder unfasten the ladder from the deck and pull the ladder from the
pool. Remove the two plugs and lay the ladder on its side to allow the majority of the water to drain out
of it. A small amount of water left in the ladder will not cause any damage. Replace the plugs into the fill
holes so that they do not get lost. The ladder may be left outside.
Large
Barrier
Small
Barrier
Foam
Pads
Screws
Use a little liquid soap to help
with ladder assembly.
OPTIONAL CONVERSION KIT
To easily convert your A-frame ladder to a deck/inpool ladder order
our #CK100-X conversion kit. The kit includes all parts and
hardware needed.
Deck cannot be higher than the pool top ledge.
IMPORTANT: LADDER ADAPTER KIT
LAK
kit fits Confer A-frame ladders for use with non-traditional
metal framed swimming pools with a wall height of 48” - 54”.
Use with models: 7100b, 7100x, 7000x, 7000b, 7200 and 8100X.
Not for use with inflatable pools.
LAK KIT
