Conductix-Wampfler MultiLine 0835 Скачать руководство пользователя страница 42

Страница: 42 / 81

Mounting Instruction

Conductor rail system

MultiLine 0835

MAL0835-0001c-EN
www.conductix.com

translated document

page 42 of 81

Fitting the hanger clamps

The hanger clamps must be fitted with expanding rivets. The expanding rivets must be driven into the holes with a plastic hammer.

CAUTION!

The hanger clamp clips have to point upwards!

→

Make sure that the hanger clamps are fitted in the
correct positions, see section Fig. 22.

→

Fit the hanger clamps (take note of the correct
intervals, see section 6.2.3).

CAUTION!

→

Check the expanding rivets' fit immediately
after fitting.

This is because once the conductor rails are fitted they
can no longer be changed!

Fig. 22: Positioning and fitting the hanger clamps

Fig. 23: Side view of a hanger clamp

Hanger clamp

Expanding rivet

Clip

Содержание MultiLine 0835


















































































Результаты поиска

Содержание MultiLine 0835

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler MultiLine 0835, Инструкция по монтажу

Результаты поиска

Содержание MultiLine 0835

Отзывы:

Бренды по названию

Популярные бренды