Conductix-Wampfler 0813 Series Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 108

background image

Operating Instructions

Insulated Conductor Rail System

SinglePowerLine Program 0813

BAL0813-0007-EN
www.conductix.com

translated document

page 97 of 108

10

Troubleshooting

10.1

Safety

Wear recommended protective equipment:

WARNING!

Danger of injury due to improper troubleshooting!

Improper troubleshooting can result in serious injury to person and property.

→

Contact the manufacturer in case of malfunction.

→

Allow troubleshooting to be conducted only by personnel from or authorized by the

manufacturer.

The faults that, to Conductix-Wampfler's best knowledge, tend to arise are listed in the following table (see Section 10.2) together
with their corresponding corrective measures.

CAUTION!

Before working on these components!

→

Switch off the power supply to the

conductor rail system

according to the 5

Safety Rules

and secure it against switching on again

. For the 5 Safety

Rules, see Section 2.5.

DANGER!

Risk of death due to electrical shock!

Contact with components carrying electrical power can lead to death or severe injury due to
electrical shock. Danger of injury due to shock reactions, falling or being thrown across the room
due to electrical shock.

→

Disconnect all line feeds from the voltage supply.

→

When decommissioning, check whether a voltage is still present in the components and
take measures where necessary.

→

The hazard zone must be enclosed by the customer or protected through distance.

→

The customer must provide grounding for metallic components.

→

The customer must provide protective devices.

→

Ensure that there is sufficient stability in the area.

→

If a conductor rail heating is available, this must also be switched to a voltage-free state.

Care must be taken to ensure that each individual heating circuit is voltage-free.

«
...
95
96
97
98
99
...
»

Содержание 0813 Series













































































































Отзывы:

Нет отзывов

Похожие инструкции для 0813 Series

Бренд: Jasic Страницы: 20

BrewZilla 100L - Gen 4

Бренд: KegLand Страницы: 48

AUTOPULSE IQ-318

Бренд: Notifier Страницы: 62

Бренд: Everlast Страницы: 30

Бренд: Firepower Страницы: 32

Universal XL HD Lifter

Бренд: Garage Smart Страницы: 21

Бренд: Kemppi Страницы: 51

Бренд: Lincoln Electric Страницы: 15

Бренд: Miller Electric Страницы: 18

Бренд: Ingersoll-Rand Страницы: 64

I/O System 750 Series

Бренд: WAGO Страницы: 50

Бренд: widos Страницы: 42

Бренд: Savant Страницы: 2

Бренд: LOGICDATA Страницы: 32

CITOTIG 250 AC/DC

Бренд: Oerlikon Страницы: 136

Бренд: Jazz Страницы: 12

Бренд: QTS Страницы: 61

Бренд: Flycolor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды