Conductix-Wampfler 0813 Series Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 108

Conductix-Wampfler 0813 Series Скачать руководство пользователя страница 50

Operating Instructions

Insulated Conductor Rail System

SinglePowerLine Program 0813

BAL0813-0007-EN
www.conductix.com

translated document

page 50 of 108

6.4.3.1

6.4.3.2

Mount hanger clamps

NOTE!

The maximum tightening torques must not be exceeded (14 Nm for a standard hanger clamp
with steel nut). Too high tightening torques will damage the hanger clamp.

NOTE!

The hanger clamp fastening must be adapted to the respective application!

The fastening elements are designed for standard fastening applications. For safety-critical fastenings,

special  on-site  interfaces  (e.g.,  deviating  through-hole  geometry  or  other  restrictions  affecting  the
fastening)  and/or  increased  requirements  (e.g.,  vibration),  the  fastening  must  be  adapted  to  the
respective  application  (e.g.,  by  means  of  additional  screw  locking  with  Loctite  242).  The  system

manufacturer is responsible for the evaluation.

Required tools:

◼

Open-end wrench, SW17

◼

Mounting comb (Order No.: 081046*)

The hanger clamps are available in versions with square nuts for mounting in support arms/C-rails (see Fig. 47) or hexagon nuts

(see Fig. 48) as well as with or without an insulator (see Fig. 12). A version with a hexagon nut is recommended for current collector
insertion from the side.

Insulators are required for indoor applications with high levels of pollution and outdoor applications and allow a rated voltage of up to
1000 V (with current collector insertion from below).

Fig. 47: Hanger clamp with square nut

Fig. 48: Hanger clamp with hexagon nut

«
...
48
49
50
51
52
...
»

Содержание 0813 Series













































































































Отзывы:

Нет отзывов