manualshive.com logo in svg

Condair GC 130, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Condair GC 130 Скачать руководство пользователя страница 58

58

Maintenance

Condair GS

 

xxxxxxx_A_EN_1905_Condair-GS_OM  

6.5.9  Resetting Service Reminder

Reset the service reminder messages and maintenance warnings in the control software after perform

-

ing the required scheduled maintenance: 

1.  Menu > Service > General Service tab > Reset Service Reminder. A reset dialogue appears and 

prompts you to confirm the reset.

2.  Select the <Yes> button on the confirmation screen. Select the <No> button to abort the reset.

6.5.10  Installing Software Updates

All software updates can be downloaded from www.condair.com. Download the file and extract it to a 

USB memory stick that has been formatted to 32-bit FAT system. The software update file (ending with 

.bin) should be located at the root level on the USB stick.
Install the updates for the control software as follows:

1.  Set the On/Off button to the Off position and disconnect the power supply to the humidifier at the 

external disconnect switch. To prevent accidental power-up, lockout and tag out according to the 

established safety practices at your facility.

2.  Remove the door panel on the control cabinet – refer to 

"Removal and Installation of Access Panels" on 

page 50

 and swing the front panel open.

3.  Carefully insert the USB memory stick into the USB port. The maximum 

length of the memory stick 

should not exceed 75 mm (3 in)

.

4.  Close the front panel, and install the door panel.
5.  Remove the lock and tag from the external disconnect switch, and restore power to the humidifier.
6.  Set the On/Off button to the On position. 
7.  When the Home screen appears, select the <Menu> button, then enter the password to login. 

CAUTION!

Risk of file corruption!

DO NOT 

interrupt software updating once it starts.

 

Wait until updating is completed. Corrupted 

control software can render the humidifier unusable.

Note:

 

If software updating is accidentally interrupted, the humidifier will not operate. However, 

updating can be resumed by leaving the USB key inserted in the board and power cycling the 

unit. The integrated control board will detect that the software was not installed properly, and 

restart the updating.

8.  Select Administrator > Software Settings tab > Software Update to update the control software. 

A progress bar shows the status of the updating process. When updating is completed, the Home 

screen is displayed.

9.  Repeat Step 1 to Step 4, and carefully remove the USB memory stick.
10. Close the front panel. Install the door panel, making sure that it is fastened securely.
11. Repeat Step 5

 and 

Step 6 to power up the humidifier.

Содержание GC 130









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды