CONCORD NT30 Скачать руководство пользователя

Страница: 88 / 150

3.18 Toolbar down pressure

A hydraulic cylinder (1) applies toolbar down

pressure on each toolbar (2). The cylinders apply a

constant down pressure through the full range of

movement of the toolbar. An active hydraulic circuit

maintains uniform pressure to each hydraulic

cylinder.
Use the terminal to set the toolbar down pressure.

The toolbar down pressure can be adjusted from

1034 kPa to 17237 kPa (150 psi to 2500 psi). Set

the toolbar down pressure high enough for correct

disc penetration and correct soil compaction. The

toolbar down pressure adjustment will change with

field conditions, seed depth, soil type, and ground

speed.
Operate the tractor hydraulic remote that the

toolbar down pressure is connected to at full output

or fully open. Operating the hydraulic remote at full

output reduces the back pressure on the toolbar

down pressure return lines.

GUID-A648413B-A2E9-4F55-9FD6-1A88664CA7C9-high.jpg [High]

Fig. 56

GUID-D2020422-6B91-4858-96B8-9A2D44137933 [V1]

3. Operation

Narrow-Transport Grain

Drill (322782B)

Содержание NT30























































































































































Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды

CONCORD NT30, Руководство оператора

Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды