CONCORD NT30 Скачать руководство пользователя

Страница: 84 / 150

GUID-A25C4E81-A124-4916-9CC9-E8E09AA8C741-high.jpg [High]

Fig. 49

3.16.6.3 Initial seed depth collar sequences

The initial seed depth collar sequence is the total length of the depth collars installed on the shaft of the

frame height cylinders. The initial seed depth collar sequence is a starting point. The sequence of depth

collars will change with the field conditions.
Use the following initial seed depth collar sequences when checking seed depth.

•

Small Grains and Beans:

7.5 inch

(

19.1 cm

) sequence (blue (2), silver

(1))

•

Canola:

9.75 inch

(

24.8 cm

) sequence (blue (2), silver (2), green (1))

3.16.6.4 Adjust the seed depth
Procedure

Raise the drill frame to the highest height.

Install the recommended initial sequence of

depth collars (1) on the shaft of each of the

frame height cylinders (2).

NOTE:

See the decal on the front of the

frame for the sequence of seed depth

collars.

Operate the drill in the field and check the

seed depth.

Adjust the sequence of seed depth collars.

Check the seed depth until the seed is at the

correct seed depth.

GUID-877F7751-7D53-4D5E-957E-2CFEBA25CC2E-high.jpg [High]

Fig. 50

GUID-EB8082A6-B93C-4BC2-BB92-6F546A9F4EFA [V1]

GUID-649A31C4-6A66-485B-B9C6-86C9A52AB443 [V3]

3. Operation

Narrow-Transport Grain

Drill (322782B)

Содержание NT30























































































































































Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды

CONCORD NT30, Руководство оператора

Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды