manualshive.com logo in svg

Concept Z Performance 350Z, Руководство по установке

Поделиться
Скачать
Concept Z Performance 350Z Скачать руководство пользователя страница 11

 
 

19. Remove the upper left mounting bolt for the drivers side crash support leg (top circle). This is where the long 

upper oil cooler bracket will mount to. Removing the aluminum crash bar is not necessary but does free up 
space and makes the install easier. The lower bracket will mount using the 2 rivnuts (bottom circles) installed in 
step #7. 

 

 

20. Now move the cooler into position and screw the two 10mm bottom mounting bolts into the rivnuts installed in 

step #7, as well as the 12mm upper bolt that holds the upper brackets. 

 

 

21. Attach the 90 degree lines to the -10 AN fittings on the cooler core and tighten them down. 

 

22. Now that the oil cooler kit is fully installed, fill the car up with the manufacturer recommended amount of oil. We 

recommend filling the car with an extra half quart of engine oil since the lines and cooler most likely still have 
some air trapped inside them. 

 

23. Start the car and check for oil leaks from the lines or cooler. If any leaks are found, shut the car off immediately 

and tighten the loose fitting. Repeat step #23 until no oil leaks are present. 

11 

Содержание 350Z













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды