USER MAINTENANCE
INSTRUCTIONS
DETACHABLE SHAVING HEAD
You will need to remove the shaving head in
order to clean the cutting assembly, and before
installing the trimmer attachment. The shav-
ing head contains the cutting assembly of the
CleanHead™ unit, comprised of the shaving
foils and inner cutters.
To remove the shaving head:
Pull head up to
separate from housing.
To attach the shaving head:
Align the marks
on the head and on the housing, and push head
down until it snaps into place. Note: The shaving
head will fit only one way.
CLEANING THE CUTTING
ASSEMBLY
1. Remove the shaving head
as instructed above.
2. Holding the shaving head
in one hand, turn it over to
expose the internal plastic
mechanism. Do not place
head upside down on any
surface, as this may damage the shaving foils.
3. Grab the two locking tabs and squeeze them
toward one another to
release the cutting assem-
bly.
4. Lift cutting assembly off
the shaving head.
5. Blow between the cutters
and tap the shaving head
softly to remove hair clippings.
6. Snap the cutting assembly back into the shav-
ing head and replace the shaving head onto the
CleanHead™ housing.
OILING THE INNER CUTTERS
To ensure maximum cutting performance, we
recommend that you lubricate the inner cut-
ters occasionally. Release the cutting assembly,
as described above. Hold the cutting assembly
upside down and apply a few drops of light
mineral oil to the front and sides of inner cutters.
Wipe excess oil off with a soft, dry cloth.
CLEANING THE TRIMMER ATTACHMENT
Clean the blades of the trimmer attachment
after each use with the cleaning brush provided.
Important: Remove trimmer attachment from unit
before cleaning. (Remove trimmer attachment in
the same way as the shaving head).
BATTERY REMOVAL
Using a Phillips head screwdriver, remove the
screws from the top and inner housing of the
shaver. Lift and remove the printed circuit attached
to the batteries. Very carefully disconnect the con-
nections before removing the batteries.
CAUTION:
Beware of any sharp edges.
LIMITED FIVE YEAR WARRANTY
Conair will repair or replace (at our option) your unit free
of charge for 60 months from the date of purchase if the
appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective
product to the service centre listed below, together with
your purchase receipt and $5.50 for postage and han-
dling. In the absence of a purchase receipt, the warranty
period shall be 60 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE 60 MONTH DURATION
OF THIS WRITTEN, LIMITED WARRANTY.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, WHATSOEVER.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from province
to province.
THIS UNIT HAS NICKeL-MeTAL HYDRIDe
BATTeRIeS. IN AN eFFORT TO PROTeCT THe
eNVIRONMeNT, THeSe BATTeRIeS SHOULD
Be ReMOVeD AND PROPeRLY DISPOSeD OF
WHeN THe UNIT IS NO LONGeR OPeRATING. TO
ReMOVe THe BATTeRY BLOCK FOR DISPOSAL
OR ReCOVeRY, FOLLOW THeSe INSTRUCTIONS:
ALIGN MARKS ON
HeAD AND HOUSING
INNeR CUTTeRS
Angled shaving foils/
attachement
Shaving head
ON/OFF
switch
Soft
universal
grip
Charging jack
Charging stand
Cleaning brush
Taper control
3 combs
Trimmer attachment
Cover
Adapter
clean up the hairline.
To trim around the ear, hold
the clipper on its side, fac-
ing down, and use the corner
of the trimmer in an arching
motion to get a clean edge to
the hairline around the ear.
ADjUSTABLE 3-POSITION TAPER CONTROL
The taper control switch at the back of the
trimmer attachment lets you gradually adjust
the closeness of the cut. For the closest cut and
the shortest hair, push taper switch all the way
to the right. To increase cutting length, slowly
push switch to the left. The three hair length
settings, from left to right, are 2.8mm, 1.8mm
and 0.8mm.
Packed-in hair can slow down any set of cutting
blades. To clean the blades, remove trimmer
attachment and brush the hair from the blades
using the cleaning brush provided. If you do this
after every use, especially with heavy hair cut-
ting, the blades should remain free of cut hair.
If the blades stop cutting but do not stop running,
then it is time to replace the trimmer attachment.
STOP. COMB. CHECK.
For best results, do as the professionals do: comb
hair often, and check cutting results as you comb
to avoid unevenness.
SERVICE CENTRE:
CONAIR CONSUMER PRODUCTS INC.
100 Conair Parkway
Woodbridge Ontario, L4H OL2
©2009 CONAIR CONSUMeR PRODUCTS INC.
For more information on any Conair product call:
1-800-472-7606
Visit our Web site:
www.conaircanada.ca
Consumer Call Centre e-mail:
[email protected]
09CN12735
IB-9102
