Comtrol WR7802-XT Series Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 128

background image

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

System | NAT Settings | Advanced Page - 59

Configuration Using the Web User Interface

System | NAT Settings | Advanced Page

You can use the

NAT Advanced

page to randomize NAT port mapping. Select

Enable

in the drop list and then

click the

Apply

button.

Note:

You must

Save

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

Power Over Ethernet Pages

The Power over Ethernet ports is one of the main features of the router. Each PoE port is compliant with both
IEEE 802.3af and 802.3at. Use the Power over Ethernet Configuration pages to configure:

•

Power over Ethernet | PoE Control Page

•

Power over Ethernet | PoE Schedule Page

•

Power over Ethernet | PoE Status Page

Power over Ethernet | PoE Control Page

This page is used to configure the Power over Ethernet parameters for the ports.

Note:

During the PoE operation, the surface accumulates heat and causes the surface temperature to become
higher than the ambient temperature. Remember NOT to touch device surface during PoE operation.

DO NOT TOUCH THE DEVICE
SURFACE DURING PoE OPERATION
- HIGH POWER FEEDING.

If

Forced

mode is selected, power is provided even if no Ethernet cable is plugged in. Only use

Forced

mode

if you are attaching a device that is capable of receiving power through its Ethernet connection.

Beta

Version

«
...
59
60
61
62
63
...
»

Содержание WR7802-XT Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR7802-XT Series

Бренд: Mafell Страницы: 162

Бренд: QUNDIS Страницы: 42

Бренд: M-system Страницы: 4

Бренд: Kramer Страницы: 56

Бренд: Kasda Страницы: 39

Бренд: ExtraHop Страницы: 3

Бренд: Paradyne Страницы: 28

Бренд: Open House Страницы: 2

Бренд: National Instruments Страницы: 72

Бренд: RadioLabs Страницы: 10

Бренд: Cambium Networks Страницы: 39

Бренд: D-Link Страницы: 32

DGS-1016D - Switch

Бренд: D-Link Страницы: 74

DGS-2208 - Desktop Switch

Бренд: D-Link Страницы: 37

DGL-4500 - GamerLounge Xtreme N Gaming Router Wireless

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 124

Бренд: D-Link Страницы: 28

DGS-1016D - Switch

Бренд: D-Link Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды