background image

8 - RocketLinx ES8108/ES8108F  User Guide

: 2000514 Rev. B

LED Indicators

Introduction

LED Indicators

There are system diagnostic LEDs and Ethernet Port LEDs located on the front panel of the RocketLinx ES8108/ES8108F. 

The LED indicators provide administrators with real-time system status. The following table describes the function of each 

LED indicator Refer to the figure in 

Front Panel

 on Page 7 for LED locations.

Packet Forwarding Ability

The RocketLinx ES8108/ES8108F features a packet filtering function for broadcast packet control protection and Quality of 

Service (QoS). Both features can provide higher performance in a crowded network through traffic filtering and prioritization.
This subsection will introduce the principles of traffic control and forwarding precedence, including Broadcast control and 

Quality of Service.

Broadcast Control

The RocketLinx ES8108/ES8108F begins to drop broadcast packets with DA (destination address) equal to 

FF:FF:FF:FF:FF:FF if the received broadcast packets are more than the threshold – 198 packets/ per second at 100Mbps or 19 

packets / per second at 10Mbps link speed.
All ports are enabled with this function by default to provide better network performance and prevent congestion caused by the 

flooding of broadcast packets.

Quality of Service

The RocketLinx ES8108/ES8108F supports the frame type priority function, where high priority packets will be queued to a 

high priority queue to share more bandwidth. The ratio of bandwidth of the high priority to the low priority queue is 8:1. After 

8 high priority packets are processed, then 1 low priority packet is processed.
Both the RocketLinx ES8108 and RocketLinx ES8108F can examine the specific bits of VLAN Tag and TCP/IP TOS of IPv4 

and IPv6.

LED Status

Description

PWR1

Green on

Power is on.

Off

No power is being supplied.

PWR2

Green on

Power is on.

Off

No power is being supplied.

Alm

Red on

Port link down or power failure event occurred.

Off

No event.

Port 1- 8 

(RocketLinx 

ES8108)

Port 1- 6 

(RocketLinx 

ES8108F)

Link (Green on)

A network device is detected and linked up.

Activity (Green blinks)

The port is transmitting or receiving packets from the connected 

device.

Speed (Yellow on/ 100Mbps) A network device is detected and link established at 100Mbps.

Speed (Yellow off)

A network device is detected and link established at 10Mbps.

Fiber port #7, #8 

(RocketLinx 

ES8108F)

100Mbps Link (Green on)

The port is operating in full-duplex mode.

100Mbps Activity (Green 

Blinks)

The port is transmitting or receiving packets from the connected 

device.

Содержание RocketLinx ES8108





















Отзывы: