Comtrol DeviceMaster ATS-XPE Скачать руководство пользователя страница 86

Страница: 86 / 96

Appendix D. Changing BIOS Configuration

PNP/PCI Configuration

This menu is used to assign IRQ numbers to your PNP/PCI devices manually.
This figure illustrates the DeviceMaster ATS-XPE factory defaults.

•

PNP OS Installed:

If you install a Plug and Play operating system (OS), the

OS will reassign the interrupt even if you choose

Yes

for this option. If you

install a non-Plug and Play OS or if you want to prevent the OS from
reassigning the board’s IRQ settings, choose

for this option.

•

Resources Controlled By:

Select

Auto

if you want the computer to assign the

IRQs.

•

Reset Configuration Data:

Enabling this field means you allow the

configuration data to be reset.

•

IRQ-xx assigned to

: These fields show whether a certain IRQ is used by a

PCI/ISA card.

Manual

Used MEM base addr : N/A

Содержание DeviceMaster ATS-XPE

































































































Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды

Comtrol DeviceMaster ATS-XPE, Руководство по установке и настройке

Результаты поиска

Содержание DeviceMaster ATS-XPE

Отзывы:

Похожие инструкции для DeviceMaster ATS-XPE

Бренды по названию

Популярные бренды