SLM-5650C / SLM-5650C-ODU Satellite Modem
Revision 1
Serial Remote Control
7–34
MN-SLM-5650C
Parameter
Type
Command
(Instruction
Code and
Qualifier)
Arguments
for Command
or Response
to Query
Description of Arguments
Response to
Command
Query
(Instruction
Code and
Qualifier)
Response to Query
Retrieve next
5 unread
AUPC Log
Entries
N/A
155 bytes
Query only.
Unit returns the oldest 5 AUPC Log Entries which have not yet been read
over the remote control.
Reply format: {CR}Sub-body{CR}Sub-body{CR}Sub-body{CR} Sub-
body{CR}Sub-body, where Sub-body=
AA.ABB.BCCC.CEEE.Eddmmyyhhmmss:
AA.A = Minimum Eb/No during sample period.
BB.B = Average Eb/No during sample period.
CCC.C = Max Output Power during sample period.
EEE.E = Average Output Power during sample period.
If there are less than 5 events to be retrieved, the remaining positions
are padded with zeros. If there are no new events, the response is RNA*.
N/A
RNA?
RNA=
{CR}AA.ABB.BCCC.CEEE.Eddmmy
yhhmmss{CR}AA.ABB.BCCC.CEEE.
Eddmmyyhhmmss{CR}AA.ABB.BCC
C.CEEE.Eddmmyyhhmmss{CR}AA.
ABB.BCCC.CEEE.Eddmmyyhhmms
s{CR}AA.ABB.BCCC.CEEE.Eddmm
yyhhmmss
(see Description of Arguments)
AUPC
Remote
Carrier Loss
Action
RCL=
1 byte
Command or Query.
Tx Output Power level setting when remote carrier is lost, where:
0=Hold current output power level
1=Goto Nominal output power level
2=Goto Maximum output power level
Example: RCL=0
RCL=
RCL?
RCL*
RCL#
RCL?
RCL=x
(see Description of Arguments)
Remote
Modem
Pattern
Substitution
RPB=
1 byte
Command or Query.
Remote Modem Tx Pattern Substitution, where:
0=Off
1=On
Note: For compatibility reasons, only the 2047 Tx pattern can be turned
On or Off at the remote modem.
Example: RPB=1 (Turn on remote modem AUPC Control)
RPB=
RPB?
RPB*
RPB#
RPB?
RPB=x
(see Description of Arguments)
Remote
Modem
AUPC
Enable
RPC=
1 byte
Command or Query.
Remote Modem AUPC Control, where:
0=Off
1=On
Example: RPC=1 (Turn on remote modem AUPC Control)
RPC=
RPC?
RPC*
RPC#
RPC?
RPC=x
(see Description of Arguments)
Remote
Modem
BERT BER
N/A
6 bytes
Query only.
Unit returns the value of the remote modem’s BERT BER in the form a.b
x 10
-c
. First three bytes are the value. Last two bytes are the exponent.
Returns 0.0E00 if the BERT is not synchronized to a pattern.
Example: RPE=4.0E06
N/A
RPE?
RPE=a.bEcc
(see Description of Arguments)
Содержание SLM-5650C CyberLynx
