Comtech EF Data CRS-180 Скачать руководство пользователя страница 78

Страница: 78 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Cables and Connections

Revision 11

5–20

5.3.2 Modem-to-User Data Interface Connections and Examples

In addition to the control and IF switch-to-modem cabling shown in the previous section, a

number of data interface configuration kits are available for use with the CDM-760 or CDM-750.

5.3.2.1 Gigabit Ethernet Data Interface Example

The CDM-760/-750 provides a ‘J7 | OPTICAL’ port and two Plug-In Interface Card (PIIC) slots for

optional data traffic handling. Both modems otherwise feature two 10/100/1000 Gigabit

Ethernet RJ-45 data interface ports by default. Figure 5-18 shows a block diagram and cabling

example for a CDM-760/-750 1:1 modem configuration using these RJ-45 ports (this example

shows use of both ports). This configuration requires no cabling and component kit – you must

use user-provided Ethernet cables and Layer 2 switches for direct connection to the modems.

CDM-760 or CDM-750 Block Diagram – 10/100/1000 Gigabit Ethernet Interface

Figure 5-18. CDM-760 or CDM-750 Gigabit Ethernet 1:1 Example

Содержание CRS-180






































































































































Результаты поиска

Содержание CRS-180

Отзывы:

Comtech EF Data CRS-180, Инструкция по установке и эксплуатации, Страница: 78 / 134

Результаты поиска

Содержание CRS-180

Отзывы: