Comtech EF Data CRS-180 Скачать руководство пользователя страница 38

Страница: 38 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Switch Connectors and Pinouts

Revision 11

3–4

Connection Instructions: Press down the tab on the cable plug, and then insert the plug into the

RJ-4

jack. The connection is complete when the tab ‘clicks’ into position inside the jack.

3.2 CRS-180 User Connectors

3.2.1 Modem Side Connectors

The modem side connectors (Figure 3-3) provide all necessary external connections between the

CRS-180 and the compatible Comtech EF Data modems.

Tx B

Tx A

Control A

Control B

Rx B

Rx A

Figure 3-3. CRS-180 – Modem Side Connectors

3.2.1.1 IF Connectors (50

Ω

BNC)

our 50

Ω

BNC female connectors are provided on the modem side of the CRS-180.

Table 3-1. Modem Side Type ‘BNC’ Connectors

Ref Des

Name

Connector Type

Function

Rx A

BNC

IF Input to Modem ‘A’

Rx B

BNC

IF Input to Modem ‘B’

Tx A

BNC

IF Output from Modem ‘A’

Tx B

BNC

IF Output from Modem ‘B’

Содержание CRS-180






































































































































Результаты поиска

Содержание CRS-180

Отзывы:

Comtech EF Data CRS-180, Инструкция по установке и эксплуатации, Страница: 38 / 134

Результаты поиска

Содержание CRS-180

Отзывы: