Comtech EF Data CRS-180 Скачать руководство пользователя страница 37

Страница: 37 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Switch Connectors and Pinouts

Revision 11

3–3

3.1.1.5 Type ‘SMA’ (Subminiature Version ‘A’)

Type ‘SMA’ connectors feature a Threaded Coupling design similar to

Type ‘TNC’, Type ‘N’, and Type ‘F’ connectors.

3.1.2 D-Subminiature Cable Connections

Type ‘D’ Connection Type

Example

Chassis Receptacles:

(TOP) Female

(BOTTOM) Male

Type ‘D’ Cable With Jack Screws

(Female Shown)

Figure 3-2. D-Subminiature Connector Examples

D-Subminiature connectors are also called Type ‘D’ or ‘D-Sub’ connectors. The connector pair

features multiple rows of pins (male side) coupled to mating sockets (female side). The cable

plug and chassis receptacle each feature a D-shaped profile that interlock to ensure proper pin

orientation and connector seating.

Either chassis receptacle gender features two jack nuts for secure assembly of the cable plug to

the chassis receptacle.

Whether its gender is male or female, the cable plug features two jack screws for secure

connection to the jack nuts provided on the mating chassis receptacle. The jack screws may be

hand tightened or tightened with a standard flat-blade screwdriver.

Connection Instructions: Orient the plug to the receptacle in the proper position. Press firmly

into place. Use the jack screws to secure the plug to the receptacle jack nuts. Do not over-

tighten.

About connector pinout tables: Figure 3-2 identifies the Pin 1 location for either gender

connector. Unless noted otherwise, the connector pinout tables provided in this manual

arrange/order information (i.e., the Pin # column/row) based on this orientation.

3.1.3 RJ-45, RJ-48 Cable Connections

The plug for an RJ-45 or RJ-48 cable features a flexible tab. The RJ-45

or RJ-48 jack features a mating slot. This design configuration assures

proper installation and pin orientation.

Содержание CRS-180






































































































































Результаты поиска

Содержание CRS-180

Отзывы:

Comtech EF Data CRS-180, Инструкция по установке и эксплуатации, Страница: 37 / 134

Результаты поиска

Содержание CRS-180

Отзывы: