Computec CDD6 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 74

Computec CDD6 Скачать руководство пользователя страница 17

Computec

CDD6

EN

CDD6: user manual – rev.07

Page 17/74

3.6

Door set-up, Learning and Functional tests

Once the physical installation phase described in the previous paragraph is completed, it is possible to
proceed with the power ON of the device and its configuration. In case of problems during the execution of
the phases, please refer to the paragraph 6.2. Refer to paragraph 4.3.2 for the front panel use.

STEP

Operation

Description

Notes

1

Power supply test

Connect the main power supply.

Press

key and checks the front panel display as

indicated.

Then press

key.

“88” followed by
“- -“

2

AUTOSET execution

Put the door panels near to the panels closed position

(gap<10cm), then press and

keep pressed

key

on

the door drive front panel.

Press

key, checking that “SL” is shown on the door

drive display,

then release key

.

Floor with DTBC contact active (not available for
magnetic switches application)

: AUTOSET for second TB

floor will start automatically.

The door starts the auto-set procedure auto-detecting:

-

the closing rotation

-

the skate space

-

the door movement space

-

the door closing torque profile to optimize the
closing force detection

-

the opening profile.

In case the of errors or alarms, proceed with the checks
suggested in the user manual.

To optimize the execution of the learning procedure, it
is suggested but not necessary to couple car and landing
door, executing the operations from the car roof in
inspection mode.

The learning phase is completed.

NORMAL, INSP. and
CONFIG LEDS are all
ON

“SL” fixed

Auto-set for DTBC
contact: “S2” fixed

In case or error:
“Er” alternate to the
error code
In case of alarm “AL”
alternate to the
alarm code

“OP” fixed

8
8

«
...
15
16
17
18
19
...
»

Содержание CDD6











































































Отзывы:

Нет отзывов