Computec CDD6 Скачать руководство пользователя страница 28

Страница: 28 / 74

Computec

CDD6

CDD6: user manual – rev.07

Page 28/74

4.3.2

HMI user interface description

The CDD6 door drive has a front panel that allows to activate different functional modes: Normal,
Inspection, Configuration.

MODE

NORMAL

INSPECTION

CONFIGURATION

Description

Normal mode (automatic):

the door drive executes the

commands from MLC

Inspection mode (manual):

the door drive executes

commands from the front

panel keys

Configuration mode: parameters

Programming

LED

NORMAL

OFF

INSP

OFF

CONFIG

OFF

KEYS

Key 1 and key 4 pressed
together per t>3s:
Configuration mode access

ENTER

Access to parameter value
OR
Parameter value saving and
return to parameters list

Pressed and keep pressed
(t>3s):
Last alarm code showed (“no
AL” if no alarm present)

Door opening

Pressed and keep pressed
(t>5s)  together key 3: enable
or disable Motor torque

Increase Parameter index,
OR
Increase Parameter value

Pressed for t>3s when last
alarm is showed: reset of the
last alarm codes (“no AL”)

Door closing

Pressed and keep pressed
(t>5s) together key 2: enable
or disable Motor torque

Decrease Parameter index,
OR
Decrease Parameter value

Access to Inspection mode (if
only key 4 pressed for t>1s)

Access to Configuration mode
(if key 1 and key 4 pressed
together for t>3s)

Return to Normal mode

ESC

Exit from parameter selection
OR
Exit from Configuration mode
and return to Normal mode

DISPLAY

Door drive status showed:
“- -“, “OP”, “CL”, “IM”, “AL”, ..

Parameter list: “P” alternate to
the parameter index.
Parameter modification:
parameter value showed

NOTES

This is the default mode at the
power ON of the door drive.
ALL inputs are active

DOC and DCC signals from the
MLC are not active

Parameter selection: “P” showed
alternate to the parameter index

- Table 16: functional table of the CDD6 front panel -

8
8

Содержание CDD6











































































Результаты поиска

Содержание CDD6

Отзывы:

Computec CDD6, Руководство пользователя, Страница: 28 / 74

Результаты поиска

Содержание CDD6

Отзывы: