background image

Statox 560 Getting started 

 

 

Issue 12/2016 

 

Page 1 of 10 

 

 

 

Getting started with the Statox 560 

 

 

 

1

 

Safety Advice 

 

Read and observe this manual carefully. Store it in a safe place. 

 

The Statox 560 must not be operated other than in the specified ambient conditions (see 
Technical Data, page 10). 

 

In particular the regulations with regards to the protection regulations for instance DIN EN 60079-
14 must be observed. 

 

Installation must be performed by trained and authorized personnel. Only original Compur 
Monitors parts may be used. 

 

The Statox 560 must not be connected to mains! The supply voltage is 24 (16-30) VDC. 

 

All outputs of the Statox 560 may only be operated with 30 VDC. 

 

Damaged or modified sensor heads must not be used. 

 

The Ex d housing must not be opened! 

 

When  operated  in  hazardous  atmosphere,  the  sensor  head  must  be  connected  to  the  exLink 
counterpart or to a certified connection box. 

 
Disregarding these recommendations may compromise the Ex protection and result in a danger for 
personnel and assets.
 
 
 
 
 
 
 
 
 
 

This instruction is for quick orientation!  

Prior to installation and operation please download and read the detailed 

manual. Manuals in several languages are accessible on our homepage 

www.compur.com. 

 

Содержание Statox 560











Отзывы: