Name of Each Part
Wireless Setup
(Optional accessory)
Mount the Camera
Compro Technical Support Information
For any problems you may encounter, please refer to the user's manual on the
installation CD. If you need further assistance from Compro technology, you can
fill out the online help form (www.comprousa.com/feedback/) or direct email us
at [email protected].
Trademark
Compro Technology is the registered logo of Compro Technology,
Inc. C4Home and C4Home logo are registered trademarks of AVSecur
Technology, Inc. SD, SDHC and microSDHC Logos are trademarks of SD-3C, LLC.
Apple, Apple Logo, MAC and MAC OS are trademarks of Apple Inc., registered in
the U.S. and other countries. Other names and marks may be trademarks of their
respective owners.
Restriction & Disclaimer
No part of this document may be copied or reproduced in any form or by any
means without the prior written consent of Compro Technology, Inc. Compro
Technology makes no warranties with respect to this documentation and
disclaims any implied warranties of merchantability, quality, or fitness for any
particular purpose. The information in this document is subject to change
without prior notice.
Regulatory Notice
FCC Information: This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Compro Technology, Inc.
www.comprousa.com
Tel. +886 2 2918 0169 | Fax +886 2 2915 2389
4F, No.12, Alley 6, Lane 45, Pao Shin Road, Hsintien District, New Taipei City 231,
Taiwan
© 2013 Compro Technology, Inc. All rights reserved.
OK
2
1
When necessary, follow the steps below to mount the
camera on a flat surface. Then adjust the camera to the
desired viewing angle.
Detach the metal mounting plate from the bracket
by inserting a flat blade screwdriver into the rectangular
hole on the wide end of the bracket base and then
pressing the screwdriver downward.
Place the side of the mounting plate that has
protruding screw holes against the mounting surface.
Screw the mounting plate into the mounting holes on
the mounting surface. And fasten the bracket to the
mounting plate by clicking the plate into position.
Note:
When dismounting the camera, follow step 1 to
detach the camera from the mounting plate. Do not pull
the camera off the mounting surface by force, as doing
so may damage the bracket base permanently and
render future camera mounting impossible.
One-click the reset button to setup WPS
Search for available Wi-Fi access points and enter the passphrase manually
˙
Make sure the IP camera is connected to the local network via network cable.
˙
If you have the wireless adaptor for TN70, please plugged into the IP camera.
˙
The smartphone must be in the same local network in order to successfully
search and configure the camera.
˙
Start C4Home app and enter "iWizard" on the "Add Camera" page to search
your camera and set up wireless connection.
˙
After the wireless connection is successfully set up, you can remove the
ethernet cable.
Using WPS setup
˙
Make sure your Wi-Fi router supports WPS, press the WPS button on the router
and one-click the RESET button on the IP camera. The blue LED will be blinking
during the WPS setup process and resume to steady lighting when the setup
is completed.
5
4
10
9
8
7
2 3
1
14
13
11
12
6
1. Light Sensor
2. Lens
3. IR LEDs x6 (inside)
4. Microphone
5. Speaker
6. LED status indicator
7. Wireless adapter port
(Optional accessory)
8. Audio Output
9. Reset button
10. microSD card slot
11. Microphone Input
12. Power connector
13. Ethernet port
14. Digital I/O port
1
2
Note:
With the optional wireless adapter installed,
the maximum support resolution of camera
will be 640 x 480.