background image

             Installation Instructions 

 

MT21-10 Swing Set  

Required Crew: 2 Required 
Concrete: 11-12, 80 lb. bags  

Required Tools:  

● Wheelbarrow  
● Step Ladder (6’ or taller)  
● Shovel  
● Tape Measure  
● Digging Bar or Pick  
● Level  
● Allen Wrench (Provided)  
● Open end or Box Wrenches: 9/16”, ¾” 
● Hammer or Mallet  
● Ratchet Handle & Sockets: 9/16”, ¾” 
● Marker Pen  
● Drill: Cordless or electric, or impact driver  

 

Component Playgrounds is concerned about the safety of your vision. It 
is important that you choose to protect your vision by wearing proper 
safety glasses during each and every phase of this construction 
process.  

PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING  

The MT21-10 can be installed as a one day project. The normal time 
required to install the MT21-10 is about 2-4 hours for a two man crew. This 
time requirement will vary dependent upon the composition of the soil and 
the speed of the installers. Mix and pour the concrete as the last step. 

*Before digging, please obey local laws by notifying your local 
underground utilities marking organization*  

 

Содержание MT21-10
















Отзывы: