background image

14 

 

Section 5 

Maintenance and Calibration 

 

WARNING 

MAINTENANCE  AND  CALIBRATION  INSTRUCTIONS  ARE  FOR  QUALIFIED 
PERSONNEL  ONLY.    TO  AVOID  ELECTRIC  SHOCK,  DO  NOT  PERFORM  ANY 
SERVICING OTHER THAN THE CONTAINED IN THE OPERATING INSTRUCTIONS.

 

 
This section of the manual contains maintenance information for the MegaPulse Code 360 impulse tester. A 
1-year calibration cycle is recommended to maintain the specifications of the factory.  The test equipment 
required for the performance test is a digital oscilloscope, high voltage oscilloscope probe, digital meter and 
a high voltage probe. 
 

Service Information 

 
The MegaPulse tester is warranted to the original purchaser for a period of 1 year.  This warranty does not 
cover problems due to misuse or neglect.  Malfunctions which occur within the limits of the warranty will be 
corrected  at  no  charge.    Mail  the  instrument  post  paid  to  the  manufacturer.    Dated  proof  of  purchase  is 
required  for  all  in-warranty  repairs.    The  manufacturer  is  also  available  for  calibration  and  /  or  repair  of 
instruments that are beyond their warranty period.  Contact the manufacturer for a cost quotation.  Ship the 
instrument and your remittance according to the instructions given by the manufacturer.

 

 

General Maintenance 

 

 

To avoid contaminating the PWB with oil from your fingers, handle it by the edges or wear  gloves.  If the 
PWB becomes contaminated, refer to the cleaning procedures given later in this section

.

 

 

WARNING 

Dangerous  voltages  exist  when  energized.    Exercise  extreme  care  when  working  on  an 
energized circuit.

 

 

Cleaning 

 
Clean the front panel and case with a mild solution of detergent and a damp sponge. Clean dust from the 
PWB with clean, dry, low pressure (<20 psi) 

 

CAUTION 

Do not use aromatic hydrocarbons or chlorinated solvents for cleaning.  These solutions will 

react with the plastic materials used in the instrument.

 

 

Calibration Information 

 
The Calibration Procedure should be performed annually and any time the instrument has been repaired.  The 
calibration  procedure  should  be  performed  at  an  ambient  temperature  of  23

5

C  (73.4

9

F).  The 

procedure consists on internal components tolerance verification and calibrating the meter reading to agree 
with  the  capacitor  bank.  The  Calibration  procedure  must  be  performed  by  qualified  personnel,  for  more 
information contact Compliance West USA. 

 

 

Содержание MegaPulse 360























Отзывы: