Compaq Evo D510 MT страница 61 Скачать руководство пользователя

Страница: 61 / 70

C–4

Hardware Reference Guide

Battery Replacement

To insert the new battery, slide one edge of the replacement
battery under the holder’s lip with the positive side up. Push
the other edge down until the clamp snaps over the other edge
of the battery.

Replacing a Coin Cell Battery (Type 2)

✎

After the battery has been replaced, use the following steps to
complete this procedure.

5. Replace the computer cover or access panel.

6. Plug in the computer and turn on power to the computer.

7. Reset the date and time, your passwords, and any special system

setups, using Compaq Computer Setup. Refer to the

Computer

Setup (F10) Utility Guide.

If you normally lock the Smart Cover Lock, use Computer Setup
to relock the lock and enable the Smart Cover Sensor.

Содержание Evo D510 MT







































































Результаты поиска

Содержание Evo D510 MT

Отзывы:

Похожие инструкции для Evo D510 MT

Бренды по названию

Популярные бренды

Compaq Evo D510 MT, Справочник по аппаратуре

Результаты поиска

Содержание Evo D510 MT

Отзывы:

Похожие инструкции для Evo D510 MT

Бренды по названию

Популярные бренды