background image

 

12 

 

Knowhow is the difference 

Maintenance instructions 

 

General maintenance 

Follow this maintenance instruction, to preserve the wheel dolly

’s safety, performance and service life.

 

 

All moving parts must be inspected, cleaned and lubricated once a month using a moisture-displacing 

lubricant. 

 

Check the wheel dolly for oil leaks and call an authorised service technician if required.  

 

In case of rust, remove the rust and protect with a rustproofing agent. 

 

Check that locks and rollers on the unit (M, L, S, F and W) are all intact and working properly. 

 

Check that retaining rings, nuts, bolts, and mandrels are intact and working properly. 

 

Cleaning 

Ordinary cleaning with mild soap (i.e. dishwashing detergent, auto shampoo) and a soft brush. 

Thorough drying will protect the dolly

’s painted surfaces.

 

Never wash the dolly using a high-pressure cleaner, as this may damage the dolly

’s surface and 

components. 

 

Storage 

The dolly should always be stored in vertical position in a dry and temperate climate. 

 

Repair 

In case repair of the dolly is required, use only original Compac parts.  
This work must be done by a qualified hydraulics specialist.  

Use of non-original parts not supplied by Compac could make the dolly unsafe for use and nullifies the 

warranty. 

 

Oil change 

If it becomes necessary to refill oil in the double-acting cylinder, s

ee the section “Periodic maintenance and 

inspection” in section 3, and follow the instruction for action 3A. 

 

 

Oil information 

Replace the oil as needed or at every 1 - 2 years. 

Oil type: Castrol Hyspin AWS 22 or similar hydraulic oil with the same specifications.  

Do not use brake fluid, motor oil or the like! 

 

Annual maintenance 

A specialist must perform an annual safety inspection, where the following is checked: 

 

All hydraulic components must be checked for leaks. 

 

The frame, rollers and pump must be checked for wear, cracks and other damage.   

 

 

Disposal / destruction 

Re-use the transport packaging if possible, or bring it to a recycling centre.  

For service, repair or disposal of the wheel dolly, drain the oil into an approved container and bring it to the 

proper authority. For disposal of the wheel dolly, bring it to a recycling centre. 

 

 

INFO 

RECYCLING 

Содержание WD 1600


















Отзывы: