Comnet CNGE3FE7MS4 Скачать руководство пользователя страница 85

Страница: 85 / 104

INS_CNGE3FE7MS4_REV– Rev. 4.30.14 PAGE 85

INSTALLATION AND OPERATION MANUAL

CNGE3FE7MS4

TECH SUPPORT: 1.888.678.9427

Commands Set List—Port Commands Set

Commands

Level Description

Example

interface fastEthernet
[Portid]

Choose the port for modification. switch(config)#interface fastEthernet 2

duplex
[full | half]

Use the duplex configuration
command to specify the duplex
mode of operation for Fast
Ethernet.

switch(config)#interface fastEthernet 2
switch(config-if)#duplex full

speed
[10|100|1000|auto]

Use the speed configuration
command to specify the speed
mode of operation for Fast
Ethernet., the speed can’t be set
to 1000 if the port isn’t a giga
port..

switch(config)#interface fastEthernet 2
switch(config-if)#speed 100

flowcontrol mode
[Symmetric|Asymmetric]

Use the flowcontrol configuration
command on Ethernet ports
to control traffic rates during
congestion.

switch(config)#interface fastEthernet 2
switch(config-if)#flowcontrol mode
Asymmetric

no flowcontrol

Disable flow control of interface

switch(config-if)#no flowcontrol

security enable

Enable security of interface

switch(config)#interface fastEthernet 2
switch(config-if)#security enable

no security

Disable security of interface

switch(config)#interface fastEthernet 2
switch(config-if)#no security

bandwidth type all

Set interface ingress limit frame
type to “accept all frame”

switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth type all

bandwidth type
broadcast-multicast-
flooded-unicast

Set interface ingress limit frame
type to “accept broadcast,
multicast, and flooded unicast
frame”

switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth type
broadcast-multicast-flooded-unicast

bandwidth type
broadcast-multicast

Set interface ingress limit frame
type to “accept broadcast and
multicast frame”

switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth type
broadcast-multicast

bandwidth type
broadcast-only

Set interface ingress limit frame
type to “only accept broadcast
frame”

switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth type
broadcast-only

bandwidth in
[Value]

Set interface input bandwidth.
Rate Range is from 100 kbps to
102400 kbps or to 256000 kbps
for giga ports, and zero means no
limit.

switch(config)#interface fastEthernet 2
switch(config-if)#bandwidth in 100

Содержание CNGE3FE7MS4









































































































Результаты поиска

Содержание CNGE3FE7MS4

Отзывы:

Похожие инструкции для CNGE3FE7MS4

Бренды по названию

Популярные бренды

Comnet CNGE3FE7MS4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CNGE3FE7MS4

Отзывы:

Похожие инструкции для CNGE3FE7MS4

Бренды по названию

Популярные бренды