IMPORTANT-QSG: Write down all of the currently active settings
so you can restore your computer to its current configuration later
(when this process is complete).
3. Select Use the following IP address (if it is not already selected) and
make the following entries:
• IP address: 192.168.0.22 (or any available address in the
192.168.0.x network, except 192.168.0.1)
• Subnet mask: 255.255.255.0
• Default gateway: 192.168.0.1
Leave the DNS server fields empty.
4. Click OK to save your changes. Your changes go into effect
immediately.
Step 3: Logging In to the AP
NOTE: The admin PC must be directly connected to the AP through one
of the Ethernet ports and powered on, ready for setup.
1. On your admin PC, open a web browser window.
2. Enter the following URL in the browser navigation bar:
https://192.168.0.1
3. Press Enter to initiate the connection. When the security alert dialog
box displays, click OK/Yes to proceed.
4. When the Ruckus Admin login page displays, enter the following:
• Username: super
• Password: sp-admin
5. Click Login. On your first login, you will be prompted to change the
default password.
6. When the Change Password dialog box displays, enter the following:
• New Password: Enter a new password.
• Confirm Password: Re-enter the new password.
7. Click Submit.
8. Log in using the new password.
Step 4: Customizing the Wireless Settings
TABLE 2 Default AP Settings
Network Names (SSIDs)
Wireless1—Wireless8 (2.4 GHz
radio)
Wireless9—Wireless16 (5 GHz
radio)
Security (Encryption method)
Disabled for each wireless
interface
Default Management IP Address 192.168.0.1
1. On the web interface menu, click Configuration > Radio 2.4G or
Configuration > Radio 5G. The Configure > Wireless > Common page
displays.
2. Verify that the following options are active:
Channel: SmartSelect
Country Code: If you are not located in the United States of America,
select your current country.
3. Click Update Settings if you made any changes.
4. Click any of the Wireless # (Wireless LAN Number) tabs at the top of
the page.
5. In Wireless Availability, click Enabled.
6. Delete the text in the SSID field, and type a name for your network
that will help your users identify this AP in their wireless network
application.
7. Click Update Settings to save your changes.
8. Repeat for each Wireless # (Wireless LAN Number) interface that you
want to enable.
9. Click Logout to exit the web interface.
10. When the Ruckus Admin login page displays, exit your browser.
11. Disconnect the AP from the computer and from the power source,
and restore your computer to its original network connection
configuration settings.
Step 5: Placing the AP in Your Site
1. Move the AP to its permanent location (accessible to both power and
network connections). For installation instructions, refer to
"Mounting Instructions."
2. Use an Ethernet cable to connect the PoE port to an appropriate
device:
• The network device of the ISP or carrier.
• An Ethernet switch that is connected to the network device of the
ISP or carrier.
3. Connect the AP power adapter (or PoE power supply) to the AP, and
connect to a convenient power source.
NOTE: If you will be using PoE, you must use a Cat 5e (or better)
Ethernet cable to connect the AP to the PoE switch or PoE injector.
4. Verify that the PoE port LED is lit.
After a short pause to re-establish the Internet connection, you can
test the AP.
Step 6: Verifying the Installation
1. Using any wireless-enabled computer or mobile device, search for
and select the wireless network you previously configured.
2. When connected, open a browser and connect to any public website.
Congratulations! Your wireless network is active and ready for use.
Mounting Instructions
Mounting on a Drop-Ceiling T-Bar
The factory-supplied T-bar mounting assembly kit allows you to attach the
AP to recessed and flush drop-ceiling T-bars.
1. Position the studs on the bottom of the T-bar bracket (1 in Figure 3) in
the keyholes on the AP enclosure.
2. Slide the T-bar bracket away from the Ethernet ports on the bottom
of the AP until the AP retainer tab snaps into place, trapping the T-bar
bracket studs in the keyholes (2 in Figure 3).
FIGURE 3 Attaching the T-bar Bracket to the AP
3. Insert the locking tab (3 in Figure 3) so it is in the first position on the
T-bar bracket (1 in Figure 3).
4. Gently push the ceiling tiles, if present, up and out of the way.
5. Position the T-bar bracket so its two clasps grip one edge of the T-bar
(1 in Figure 4). Make sure that both clasps are gripping the T-bar.
6. Hold the AP in place and gently push the locking tab (2 in Figure 4)
until its clasp grips the other edge of the T-bar. Make sure that all
three clasps are gripping the T-bar.
Copyright
©
2020 CommScope, Inc. All rights reserved.
Page 2 of 4
Published March 2020, Part Number 800-72433-001 Rev A
Ruckus Wireless Inc.
350 W. Java Dr., Sunnyvale CA 94089 USA
