manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 85

Ruckus ICX 7750 Switch Hardware Installation Guide 

83

Part Number: 53-1003900-10

 

Ruckus ICX 7750 Cautions and Danger 
Notices

•

Cautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  83

•

Danger notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  87

Cautions

A caution calls your attention to a possible hazard that can damage equipment.

“Vorsicht” weist auf die Gefahr einer möglichen Beschädigung des Gerätes hin.

Une mise en garde attire votre attention sur un risque possible d'endommagement de l'équipement. Ci-dessous, vous trouverez les 
mises en garde utilisées dans ce manuel.

Un mensaje de precaución le advierte sobre un posible peligro que pueda dañar el equipo. Las siguientes son precauciones utilizadas en 
este manual.

CAUTION 

The procedures in this manual are for qualified service personnel.

VORSICHT

Die Verfahren in diesem Handbuch sind nur für qualifiziertes Wartungspersonal gedacht.

MISE EN GARDE

Les procédures décrites dans ce manuel doivent être effectuées par le personnel de service qualifié uniquement. 

PRECAUCIÓN

Los procedimientos de este manual se han hecho para personal de servicio cualificado. 

CAUTION 

All devices with DC power supplies (Ruckus ICX 7750 ) are intended for installation in restricted access areas only. A restricted 
access area is where access can be gained only by service personnel through the use of a special tool, lock and key, or other 
means of security, and is controlled by the authority responsible for the location.

VORSICHT

Alle Geräte mit Gleichstromeingangsschaltung (Ruckus ICX 7750 ) sind nur zur Installation in Sperrbereichen bestimmt. Ein 
Sperrbereich ist ein Ort, zu dem nur Wartungspersonal mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer anderen 
Schutzvorrichtung Zugang hat. Er unterliegt außerdem der Kontrolle durch die für den Standort verantwortliche Stelle.

MISE EN GARDE

Tous les équipements dotés d'un bloc d'alimentation en courant continu (Ruckus ICX 7750 ) sont conçus pour l'installation 
dans des zones à accès réglementé uniquement. Une zone à accès réglementé est un local qui n'est accessible que par le 
personnel d'entretien à l'aide d'un outil, verrou ou clé conçus à cet effet, ou de tout autre accessoire de sécurité, et qui est 
contrôlé par l'autorité responsable de ce local.

PRECAUCIÓN

Todos aquellos dispositivos con fuentes de alimentación de CC (Ruckus ICX 7750 ) están diseñados para su instalación en 
zonas de acceso restringido solamente. Una zona de acceso restringido es un lugar al que sólo puede acceder personal de 
mantenimiento haciendo uso de una herramienta especial, una llave y un candado, o algún otro medio de seguridad, y que está 
controlado por la autoridad responsable.

CAUTION

Do not install the device in an environment where the operating ambient temperature might exceed 50

 C (122

 F).

VORSICHT

Das Gerät darf nicht in einer Umgebung mit einer Umgebungsbetriebstemperatur von über 50

 C (122

 F) installiert werden.

MISE EN GARDE

 

N'installez pas le dispositif dans un environnement où la température d'exploitation ambiante risque de dépasser 50

 C (122

 

F).

PRECAUCIÓN

No instale el instrumento en un entorno en el que la temperatura ambiente de operación pueda exceder los 50

 C (122

 F).

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды