manualshive.com logo in svg

CommScope Ruckus ICX 7750, Руководство по установке оборудования

Поделиться
Скачать
CommScope Ruckus ICX 7750 Скачать руководство пользователя страница 42

40

Ruckus ICX 7750 Switch Hardware Installation Guide 

Part Number: 53-1003900-10

Installing the Ruckus ICX 7750

Power supplies

 

6.

When you are sure the power supply has properly engaged the connector, tighten the retainer screws to secure the power supply 
in the slot.

When the Ruckus ICX 7750 is powered on, the LEDs on the power supply rear panel should light up green to confirm that the power 
supply is correctly installed and supplying power.

Installing a DC power supply

NOTE

AC and DC power supplies cannot be installed and used in the same device. Mismatched power supplies in the same device 
cause continual reboot on power up. 

Use the following steps to install a DC power supply in the Ruckus ICX 7750.

1.

Remove the previously installed power supply from the appropriate slot by removing the chassis attachment screws located in 
the upper right and lower left of the power supply unit using a Phillips screwdriver. Refer to item 1 in 

Figure 29

.

FIGURE 29

DC power supply screws

2.

Before opening the package that contains the DC power supply, touch the bag of the switch casing to discharge any potential 
static electricity. Ruckus recommends using an ESD wrist strap during installation.

3.

Remove the DC power supply from the anti-static shielded bag.

CAUTION

If you do not install a power supply in a slot, you must keep the slot panel in place. If you run the device with an uncovered slot, 
the system will overheat.

CAUTION

All devices with DC power supplies (Ruckus ICX 7750) are intended for installation in restricted access areas only. A restricted 
access area is where access can be gained only by service personnel through the use of a special tool, lock and key, or other 
means of security, and is controlled by the authority responsible for the location.

1

Chassis attachment screws

2

Assembly screws

Содержание Ruckus ICX 7750




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды