CommScope NovuX Fiber Optic System Скачать руководство пользователя страница 14

Страница: 14 / 41

Page 14 of 41

11.3 Install grounding kit

11.3.1

Install the grounding wire to the ground bar as shown in figure 1, using a socket wrench size 8.

11.3.2

Install the feeder cable (with the strain relief bracket installed) into the organizer as shown in section 10.2.

11.3.3

Install the grounding assembly on the studs of the installed strain relief bracket using a socket wrench size 8.

Route feeder fibers to splice tray

12.1 Route subunits to storage

12.1.1

Select the subunits that will be used for splicing to the drops or branch cable. Keep them separate. Route the

subunits that will not be used to the loop storage basket. Make sure all subunits are positioned properly under the lips.
Table below gives an overview of the capacity of the loop storage basket:

Midspan

Maximum amount of subunits stored in loop storage basket

240 cm+/- 5 cm (95.5 +/- 2 inches)

8 subunits (module 6)

200 cm+/- 5 cm (78.7 +/- 2 inches)

8 subunits (module 6)

130 cm +/- 5 cm (51.2 +/- 2 inches)

12 subunits (module 6)

Feeder out

Feeder in

Feeder out

Lorem ipsum

Feeder in

Feeder out

Subunits

12.2

Directly to splice tray rear

12.2.1

Cut the subunits at the jacket end installed on side F2 (endcut) OR cut the subunit in the middle (midcut).

The non-used end can be re-stored in the loop storage.
12.2.2

Bring the cut subunit to the splice tray (rear) and mark the stripping point. Strip the subunit to this mark and clean

all fibers per standard practice.

12.3

Via uncut fiber storage

Note: Maximum 2 subunits can enter the uncut fiber storage.

The uncut fiber storage can be used with shaved subunits or with cut subunits.

12.3.1 Shaved subunit

12.3.1.1

Bring the selected subunit to the rear of the loop storage, the uncut fiber storage.

Note

: It is important that the

selected subunit is routed first and that the bundle of subunits is installed back on top of this routed subunit.

12.3.1.2

Put the selected subunit on top of the uncut fiber storage basket and indicate the marks (stripping points) between

which the subunit should be shaved. Shave and clean the subunit per standard practice. Cut the fiber to be spliced at the

jacket end of the subunit, side F2.

remove

cover

stripping

point

stripping

point

subunits

endcut

midcut

+/-1 cm

0.4”

stripping

point

stripping

point

endcut

subunits

uncut ﬁber storage

Содержание NovuX Fiber Optic System










































Результаты поиска

Содержание NovuX Fiber Optic System

Отзывы:

Бренды по названию

Популярные бренды

CommScope NovuX Fiber Optic System, Руководство по установке

Результаты поиска

Содержание NovuX Fiber Optic System

Отзывы:

Бренды по названию

Популярные бренды