background image

ADCP-90-516 • Rev B • April 2019

Page 8

© 2019, CommScope, Inc.

Figure 5. FL2000 Storage Panel 5-Inch Recess Rack Mounting Option (Top View)

4. Align the left side mounting bracket holes to the corresponding holes in the rack and

secure the panel to the rack using #12-24 screws (provided). 

5. Align the mounting holes in the right side of the panel with the corresponding holes in the

rack, and secure the panel to the rack using # 12-24 screws (provided).

3.1.2

Flush, 1-, 2- or 4-Inch Recess Mount in a 19-Inch Rack

1. Remove the front cover of the storage panel by opening the cover approximately two

inches (5 cm), then lifting the cover from the hinges (see 

Figure 1

).

2. Remove the VCG from the left side of the storage panel and install the 

narrower

 VCG

from the optional flush mount kit. 

3. Attach the adjustable mounting bracket to the side of the VCG, positioned either at the

front (for flush mounting), or one or two inches back depending on the recess required.
(See items shown in dashed lines at the left side of 

Figure 6

.)

4. Attach the chassis mounting bracket (from the optional Flush Mount Kit) to the right side

of the storage panel with the same amount of recess as the mounting bracket attached in

Step 3

. (See right side of 

Figure 6

.)

5. The storage panel must be positioned on the equipment rack so any cross-connect or fiber

optic terminal (FOT) patch cords can enter the storage panel through the VCG at the left
side of the storage panel (see 

Figure 1

). 

Note: 

To attach the storage panel flush, or with a one-inch, two-inch, or four-inch recess

from the front of the equipment rack, you will need the FL2000 Flush Mount Kit.

5 IN.

RECESS

5 IN.

RECESS

EQUIPMENT

RACK

EQUIPMENT

RACK

17108-A

Содержание FL2000 Storage Panel





















Отзывы: