background image

ADCP-90-516 • Rev B • April 2019

Page 6

© 2019, CommScope, Inc.

1.3

Fiber Storage Tray Panel

The storage tray panel is available in one storage capacity with six fiber storage trays. The panel
is 5.25 inches (13.34mm) high. A storage tray panel is shown in 

Figure 3

.

Each tray provides storage for 20m (66 feet) of 3mm patch cord and 35m (115 feet) of 2mm
patch cord when routed in bulk with an additional wrap around each of the outer two most
portions of the tray. The storage tray assemblies easily swing out of the chassis from the left side
to provide convenient access for storing patch cords. Patch cords enter and exit each tray
assembly from an opening on the edge of the assembly.

1.4

Horizontal Management Panel

The horizontal management panel has two spools to store patch cords. The panel is 5.25 inches
(13.34mm) high. A horizontal management panel is shown in 

Figure 4

.

Up to 137m (550 feet) of slack cable can be stored using an 

“oval”

 storage method. The total

capacity may be shared by several patch cords. For example, 11.4 meters of slack cable may be
stored in the panel for up to a quantity of 12-2mm patch cords.

Figure 4. Typical Horizontal Management Panel

18879-A

STORAGE

SPOOLS

VERTICAL

CABLE GUIDE

(VCG)

CHASSIS

MOUNTING

BRACKET

Содержание FL2000 Storage Panel





















Отзывы: