background image

ADCP-90-516 • Rev B • April 2019

Page 12

© 2019, CommScope, Inc.

2. Unlatch and open the bulkhead panel.

3. Select the left side mounting bracket (provided in the kit) and attach it to the VCG in the

flush, 1-, 2- or 4-inch mounting position.

4. Select the right side bracket (provided in the kit), and attach it to the right side of the panel

with the same amount of recess as the left side bracket.

5. Align the left side mounting bracket holes to the corresponding holes in the rack and

secure the panel to the rack using #12-24 screws (provided).

6. Align the right side bracket with the corresponding holes in the rack and secure the panel.

3.2

FL2000 Storage Panel ETSI Flush Mount Kit

An ETSI Flush Mount Kit is available to install a storage panel in an ETSI rack with a flush
mount (only) recess (the brackets can not be re-adjusted for a 1-, 2-, 4-, or 5-inch recess). The
ETSI Flush Mount Kit consists of a left mounting bracket (VCG base), a right side mounting
bracket, and hardware (M6 screws, star washers, and cage nuts) to install the panel in a rack.

To install a storage panel in an ETSI rack, remove the VCG base from the left side of the panel
and replace it with the ETSI Flush Mount VCG base. See 

Figure 10

Attach the right side

bracket using 4-40 screws as shown in 

Figure 10

. Before installing the panel in the rack, an M6

×

 1 cage nut must be installed in each rack mounting hole position. Attach the panel to the rack

with an M6 screw and star washer as shown in the exploded view in 

Figure 10

.

The ETSI Flush Mount Kit provides slotted holes to adjust the storage panel in the rack. The outer
brackets provide vertical, slotted mounting holes. The vertical mounting holes allow the panel to
be adjusted up or down in the rack to compensate for the uneven rack mounting hole spacing. The
horizontal mounting holes found in the storage panel (refer to 

Figure 10

) allow the panel to be

adjusted from side-to-side to align the VCG and panel with other VCGs and panels in the rack.

Note: 

Removing the front cover and opening the bulkhead panel provides access to the

mounting holes at the right side of the panel (as viewed from the front).

Note: 

The adjustable mounting bracket is rotated 180

°

 for a flush, 1- and 2-inch recess.

Содержание FL2000 Storage Panel





















Отзывы: